paging system toa

logo mms4-1MITRA MANDIRI SELARAS. CV

PRODUK DAN JASA

Mechanical and electrical contractor, maintenance and supply

WM-3210

  The WM-3210 Wireless Microphone employs a dynamic microphone capsule and is suitable for vocal applications. Thanks to the PLL-synthesizer system, 6 different operating frequencies are made available. A high output power ensures stable radio signal transmission.

Specifications

Microphone Element Dynamic microphone unit: Cardioid
Emission F3E
Frequency Range 169 – 216 MHz, VHF
Channel Selectable 6 ch
RF Carrier Power Less than 50 mW
Tone Frequency 32.768 kHz
Modulation System PLL synthesizer
Maximum Input Level 125 dB SPL
Maximum Deviation ±40 kHz, ±15 kHz (ONLY US Part.90)
Battery 6LR61 (9 V × 1)
Battery Life 10 hours (alkaline)
Indicator Power/Battery indicator (common use)
Antenna Internal antenna
Operating Temperature -10℃ to +50℃
Finish Resin, coating (change other’s)
Dimensions φ50 × 235.2 mm
Weight 250 g (with battery)
Accessory Stand adapter……1, Screw driver……1

WM-3220

  The WM-3220 Wireless Microphone employs an electret condenser microphone capsule and is suitable for speech applications. Thanks to the PLL-synthesizer system, 6 different operating frequencies are made available. A high output power ensures stable radio signal transmission.

Specifications

Microphone Element Electlet condenser unit: Cardioid
Emission F3E
Frequency Range 169 – 216 MHz, VHF
Channel Selectable 6 ch
RF Carrier Power Less than 50 mW
Tone Frequency 32.768 kHz
Modulation System PLL synthesizer
Maximum Input Level 120 dB SPL
Maximum Deviation ±40 kHz, ±15 kHz (ONLY US Part.90)
Battery 6LR61 (9 V × 1)
Battery Life 10 hours (alkaline)
Indicator Power/Battery indicator (common use)
Antenna Internal antenna
Operating Temperature -10℃ to +50℃
Finish Resin, coating (change other’s)
Dimensions φ45 × 235.2 mm
Weight 250 g (with battery)
Accessory Stand adapter……1, Screw driver……1

WM-3310

  The WM-3310 lavalier wireless microphone has been manufactured for use with a VHF system. It incorporates a cardioid pick-up pattern and has been designed for use in speech reinforcement applications. The built-in compressor-expander circuit minimizes the influence from ambient noise.
Specifications

Microphone Electret condenser microphone, cardioid
Emission F3E
Frequency Range 169 – 216 MHz, VHF
Channel Selectable 6 ch
RF Carrier Power Less than 50 mW
Tone Frequency 32.768 kHz
Modulation System PLL synthesizer
Maximum Input Level 120 dB SPL
Battery 6LR61 (9 V × 1)
Battery Life 10 hours (alkaline)
Indicator Power/Battery indicator (common use)
Antenna 1/4 wire antenna
Operating Temperature -10℃ to +50℃
Finish Resin, coating
Dimensions 62 (W) × 142 (H) × 32 (D) mm
Weight 135 g (with battery)
Accessory Screw driver……1

.

WT-3800 C01ER

  The TOA wireless tuner WT-3800 is a PLL-synthesizer controlled double superheterodyne diversity tuner to be used in VHF wireless systems. It employs a compander noise reduction circuit to minimizes the influence of the ambient RF noise.

Specifications

Power Source AC mains
Power Consumption 150 mA (13.8 V DC)
Receiving Frequency 169 – 216 MHz, VHF
Channel Selectable 6 ch
Receiving System Double super-heterodyne
Diversity System Space diversity
Output MIC: -60 dB*, 600 Ω, balanced, XLR-3-31 type connector
LINE: -20 dB*, 600 Ω, unbalanced, phone jack
MIC or LINE is selectable.
Mixing Input -20 dB*, 4 kΩ, unbalanced, phone jack
Antenna Input 75 Ω, BNC (phantom powering for antenna), 9 V DC, 30 mA (max)
Receiving Sensitivity Over 80 dB, S/N ratio (20 dBμV input, 40 kHz deviation)
Squelch Sensitivity 18 – 40 dBμV variable
Squelch System Using together of noise SQ, carrier SQ and tone SQ
Tone Frequency 32.768 kHz
Indicator CHANNEL, ANT A/B, Audio (peak, signal)
Channel Check Usable frequencies scanning
S/N Ratio Over 100 dB (A-weight, balanced output)
Harmonic Distortion Under 1%
Frequency Response 100 – 12,000 Hz, ±3 dB
Other Function Frequency select by PC, channel
Operating Temperature -10℃ to +50℃
Finish Resin, black
Dimensions 210 (W) × 44.2 (H) × 181 (D) mm
Weight 600 g
Accessory AC – DC adapter (230 V AC, 50 Hz)………1,
Option Mounting bracket kit: MB-WT3 (for rack mounting one WT-3800 unit)
MB-WT4 (for rack mounting two WT-3800 units)

WT-3810 C01ER

  TOA’s WT-3810 is a PLL-synthesizer controlled double superhetrodyne diversity tuner designed to be used with a VHF wireless system. It employs a compander noise reduction circuit to minimize the influence of ambient RF noise.

Specifications

Power Source AC mains
Power Consumption 150 mA (13.8 V DC)
Receiving Frequency 169 – 216 MHz, VHF
Channel Selectable 6 ch
Receiving System Double super-heterodyne
Diversity System Space diversity
Output -20 dB*, 600 Ω, unbalanced, phone jack
Mixing Input -20 dB*, 4 kΩ, unbalanced, phone jack
Antenna Rod antenna
Receiving Sensitivity Better than 80 dB, S/N ratio (20 dBμV input, 40 kHz deviation)
Squelch System Using together of noise SQ and carrier SQ
S/N Ratio Better than 100 dB (A-weight, balanced output)
Harmonic Distortion Less than 1%
Frequency Response 100 – 12,000 Hz, ±3 dB
Operating Temperature -10℃ to +50℃
Finish Resin, black
Dimensions 240 (W) × 35 (H) × 110 (D) mm
Weight 380 g
Accessory AC – DC adapter (230 V AC, 50 Hz)…1, Driver for channel changing…1

YW-3500

Intended for 200 MHz band wireless systems, the YW-3500 is a wall-mounted dipole antenna. It has an internal band pass filter and a booster circuit, and is equipped with an operation LED.

Specifications

Power Source 8 – 10 V DC (supplied from amplifier or tuner)
Current Consumption Under 24 mA
Receiving Frequency 168 – 216 MHz
Dipole Ratio Relative Gain 6 dB (including booster amplifier)
V.S.W.R Under 2.6
Output Impedance 75 Ω
Operating Temperature -10%%dC to +50%%dC
Mounting Hole Pitch 68.5 mm (dimensions for wiring box)
Finish Antenna/bracket : ABS resin, off white
Dimensions 197 (W) × 850 (H) × 32 (D) mm
Weight 200 g
Accessory Tapping screw (M4) for wooden wall……2,
M3.5 screw for wiring box……2,
RG-59/U sleeve……1

※ To minimize cable loss, use the RG-59/U or RG-6/U cable.

YW-3510

  The YW-3510 is a 1/4 type antenna designed to be mounted directly to the wireless tuner. It can be used for both UHF and VHF bands by adjusting the length of its element.
Specifications

Receiving Frequency Range VHF (longest): 169 – 216 MHz
UHF (shortest): 690 – 865 MHz
Antenna Gain Approx. -3 dBd
Output Impedance 75 Ω
Output Connector BNC plug
Finish Antenna element: Chrome plated brass
Other: Nickel-plated brass
Dimensions Antenna element length: (for VHF) 378 mm, (for UHF) 108 mm
Maximum connector diameter: φ15 mm
Weight 27 g

Integrated DSP & Control System

DP-K1

The DP-K1 is a 3U rack mountable Digital Audio Processor. It features an Automatic Resonance Control function that automatically generates an optimum filter curve to improve sound clarity after measuring the acoustic characteristics in architectural space. It permits flexible configuration of inputs and outputs, from 2-IN/4-OUT to 8-IN/8-OUT using the optional modules. Each function is set by a PC using the dedicated software. The settings can be stored in the unit’s internal memory and the stored preset memories can be recalled from the unit without connecting the PC.

Specifications

Power Source 100 – 120 V AC, 50/60 Hz
Power Consumption 40 W (750 mA)
Frequency Response 20 – 20,000 Hz, ±1 dB (+4 dB* input)
Input Max. 8 channels, modular construction (modules optional)
Output Max. 8 channels, modular construction (modules optional)
IO Configuration 2-IN/4-OUT, 2-IN/8-OUT, 4-IN/4-OUT, 4-IN/8-OUT, 6-IN/4-OUT,
6-IN/8-OUT, 8-IN/4-OUT, 8-IN/8-OUT

Signal Processing

Automatic Resonance 
Control Function
Parametric equalizer: 20 – 20,000 Hz, ±12 dB, Q: 0.267 – 69.249
Level Control – to +12 dB (0.5 dB steps), with polarity selector
Equalizer/Filter Parametric equalizer: 20 – 20,000 Hz, ±12 dB, Q: 0.267 – 69.249
Filtering: High-pass filter 20 – 20,000 Hz, 6 dB/oct, 12 dB/oct
Low-pass filter 20 – 20,000 Hz, 6 dB/oct, 12 dB/oct
Notch filter 20 – 20,000 Hz, Q: 8.651 – 69.249
All-pass filter 20 – 20,000 Hz, Q: 0.267 – 69.249
High shelving filter 6 – 20 kHz, ±12 dB
Low shelving filter 20 – 500 Hz, ±12 dB
Horn equalizer 20 kHz, 0 to +18 dB (0.5 dB steps)
Crossover filter: 20 – 20,000 Hz,
6 dB/oct, 12 dB/oct, 18 dB/oct, 24 dB/oct
Compressor Threshold: -16 to +24 dB* (1 dB steps)
Ratio: 1:1, 2:1, 3:1, 4:1, 8:1, 12:1, 20:1, :1
Attack time: 0.02 – 100 ms
Release time: 10 ms – 5 s
Noise gate Threshold: – to -26 dB* (1 dB steps)
Attack time: 0.1 – 100 ms
Release time: 20 ms – 5 s
Delay Delay time: 0 – 682.0 ms (0.021 ms steps)
Matrix 8 × 8
Level control: – to 0 dB (1 dB steps), with polarity selector
Preset Memory 8
Auxiliary Function Key lock function
Setting Software OS: Windows 2000/XP
Control system: 10 BASE – T/100 BASE-TX, Auto-Negotiation, RJ45 connector
Front Panel Section Preset memory recall knob: 1
Input indicator: Green LED
Output indicator: Green LED
Module Slot 
(Rear Panel)
Input module slot: 4
Output module slot: 2
Remote control module slot: 1
Operating Temperature +5℃ to +40℃
Finish Panel: Aluminum, hair-line finish, black
Others: Pre-coated steel plate, black, 30% gloss
Dimensions 482.6 (W) × 132.6 (H) × 320 (D) mm (excluding projection)
Weight 7.4 kg
Accessory Power cord (2 m) ……1,
Rack mounting bracket (preinstalled on the unit) ……2,
Rack mounting screw ……4,
Blank panel (preinstalled on the unit) ……8,
Module mounting screw (spare) ……4, CD (software) …1
Option Mic/Line input module: D-921E, D-921F, D-922E, D-922F
Stereo input module: D-936R
Digital input module: D-923AE, D-937SP
Line output module: D-971E, D-971M, D-971R
Digital output module: D-972AE, D-961SP
Remote control module: D-981, D-983

[Notes]
1. When installing the unit, never block the intake vents provided in the unit’s bottom near the rear.
2. Windows is a trademark of Microsoft Corporation.

DQ-C01

  The DQ-C01 Remote Control Module is designed to permit remote control of memory selection, output volume adjustment, and output muting of TOA’s Digital Processor DP-0206 from external equipment.

Specifications

Control Input COM and terminals 1 – 8: Open voltage: 5 V DC, short circuit current: 25 mA,
removable terminal block (9 pins)
Control Memory selection: Direct: Max. 8 memories, Binary: 16 memories
(Any one of 16 memories can be assigned to each
terminal when set for Direct” mode.)”
Control method: No-voltage make of over 500 ms/
No-voltage make pulse of over 500 ms
(No-voltage make of over 500 ms only when set for
Binary” mode.)”
Volume control (Up/Down): Direct: Max. 4 groups, Binary: Max. 10 groups
(Any output channel or channel group can be
assigned to each terminal.)
Control method: 1-step variation with no-
voltage make pulse of over 500 ms. Continuous
variation in 500 ms units with pulse of
over 700 ms.
Continuous up/down variation in 500 msec units
with the addition of no-voltage make pulse of
over 700 msec.
Continuous volume variation stops when a break
pulse is fed.
Variable range: 0 to -∞ dB
Muting (On/Off): Max. 8 groups
(Any output channel or channel group can be assigned to
each terminal.)
Control method: No-voltage make of over 500 ms/
No-voltage make pulse of over 500 ms
The above controls can be performed singly or in combination with other
controls.
Setting PC software (Windows95/98/NT compatible)*
Finish Pre-coated steel plate, black, 30% glossy
Dimensions 26.5 (W) × 76.5 (H) × 101 (D) mm
Weight 60 g
Accessory Mounting screw …2, Removable terminal plug (9 pins) …1

DQ-D01

  The DQ-D01 is a digital I/O module that expands the Digital Processor DP-0206’s input or output to 2 channels. The digital signal conforms to the AES/EBU format. Owing to the built-in sample rate converter, the module can handle signals of various sampling frequencies.

Specifications

Mode 1 Input mode
Signal format: AES/EBU (2 channels multiplexed)
Connector: BNC jack
Input impedance: 75 Ω
Input voltage: 0.5 – 5.0 V(p-p)
Sampling frequency: 32 – 48 kHz
Through output: Delivers the input signal electrically buffered.
2 Output mode
Signal format: AES/EBU (2 channels multiplexed)
Connector: BNC jack
Output impedance: 75 Ω
Output voltage: 1 V(p-p)
Sampling frequency: 48 kHz
Mode Selection Input mode or output mode (selectable by a slide switch)
Data Length 24 bit
Finish Pre-coated steel plate, black, 30% gloss
Dimensions 26.5 (W) × 76.5 (H) × 167.1 (D) mm
Weight 90 g
Accessory Mounting screw…2, Label…4
Applicable Model DP-0206

Equalizers

E-232E-232

  The E-232 has two 2/3 octave 14-point equalizers. It can be mounted in an EIA-Standard equipment rack (1-unit size).
Specifications

Power Source 220 – 240 V AC, 50/60 Hz
Power Consumption 13 W
Input +4 dB* 30 kΩ (GAIN: 0 dB), unbalanced, phone-jack and screw terminal
Output +4 dB* 1 kΩ, unbalanced, phone-jack and screw terminal
Max. Input Level +32 dB (GAIN: -12 dB)
Max. Output Level +20 dB
Frequency Response +1 dB, -2 dB (20 Hz – 20 kHz)
Total Harmonic 
Distortion
0.01 % or less at 1 kHz (rated output)
Equalization Center 
Frequency
40 Hz, 63 Hz, 100 Hz, 160 Hz, 250 Hz, 400 Hz, 630 Hz
1 kHz, 1.6 kHz, 2.5 kHz, 4 kHz, 6.3 kHz, 10 kHz, 16 kHz
Control Equalizaer 
Sliders
Boost: +12 dB, +6 dB Cut: -12 dB, -6 dB (switchable)
Gain Range ±12 dB
Highpass Filter -12 dB/oct (Adjustable cutoff frequency 15 Hz – 300 Hz)
Hum and Noise (IHF-A) -98 dB* or less (EQ: ON, HPF: 15 Hz, GAIN: 0 dB, all sliders at 0 position)
Finish Front panel : Aluminium, black Case: Steel, black
Dimensions 483 (W) × 46 (H) × 311 (D) mm (19.02″ × 1.81″ × 12.24″)
Weight 3.8 kg (8.38 lb)
Accessory Security cover …1, Security cover fixing screw …2, Rack mounting screw …4,
Rubber foot …4, Blind label …1, Power cord (2 m (6.56 ft)) …1
matching transformer

matching transformer

LT-102

  The LT-102 is an output transformer. This transformer can be easily connected to the TOA’s 1,000 series equipment using connectors.

Specifications

Impedance 600 ohm : 600 ohm
Frequency Response 30Hz〜20kHz at %%p0.15dB
Distortion Less than 0.2% (50Hz 5dB*)
Constant loss Within 1.5dB (at 1kHz 1v)
Weihgt 44g (0.1 lbs.)
Accessories Sleeve……2 Screw……4
1/3 octave active graphic equalizer

1/3 octave active graphic equalizer

E-1231

  The E-1231 is a single channel, 1/3 octave active graphic equalizer designed to allow clean, accurate audio equalization for stage, studio, or commercial applications.
Specifications

AC Line Voltage AC mains, 50/60 Hz
Power Consumption 11 W 120 V version
11 W 220 – 240 V version
Input Impedance 10 kΩ
Output Impedance 600 Ω
Frequency Response 20 Hz – 20 kHz, %%p1 dB
Max. Input Level +20 dB* at 1 kHz
Max. Output Level +20 dB* with 600 Ω load
Total Harmonic 
Distortion
0.01% or less at 1 kHz
(all sliders at 0 position, rated output)
Equalization Center 
Frequency
31.5 Hz, 40 Hz, 50 Hz, 63 Hz, 80 Hz, 100 Hz, 125 Hz, 160 Hz, 200 Hz,
250 Hz, 315 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1 kHz, 1.25 kHz, 1.6 kHz,
2 kHz, 2.5 kHz, 4 kHz, 5 kHz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 16 kHz
Controls Equalizer 
Sliders
%%p12 dB
Input Level Control %%p12 dB
Highpass Filter 12 dB per octave
(Adjustable cutoff frequency: 15 Hz – 300 Hz)
Lowpass Filter 12 dB per octave/6 dB per octave
(Adjustable cutoff frequency: 2.5 kHz – 30 kHz)
Hum And Noise -94 dB*
(EQ in, all sliders at 0 position, 20 Hz – 20 kHz B.P.F.)
Finish Pannel: Aluminum, black
Case: Steel, dark gray
Dimensions 482.6 (W) × 88.4 (H) × 317.2 (D) mm (19″ × 3.48″ × 12.48″)
Weight 4.5 kg (9.92 lb)

Mixers

Matrix Mixer

Matrix Mixer

M-9000 CE

  The M-9000 Matrix Mixer is designed to be used in conjunction with optional modules and can be configured for up to 8 inputs and 8 outputs. 9000 series modules as well as existing 900 series input modules can be used. The most appropriate modules can be selected depending on applications. It is equipped with signal processing and control functions necessary for sound reinforcement, permitting all parameters to be set at the mixer. Settings data can be stored inside the unit and called up using the keys on the front panel.

Specifications

Power Source 220 – 240 V AC, 50/60 Hz
Power Consumption 40 W
Audio Input Max. 8 channels, modular construction (modules optional)
Audio Output Preamplifier output 1, 2: 0 dB(*1), 600 Ω, balanced,
removable terminal block (3 pins)
Module Slot Analog input (slot 1 – 8): -10 dB(*1), 10 kΩ, unbalanced
Digital input (slot 1 – 4): 24 bit/48 kHz
MIX output (slot 1 – 8): -14 dB(*1), 330 Ω (CH 1 prefader output), unbalanced
Digital output (slot 5 – 7): 24 bit/48 kHz
Power supply (slot 1 – 8): +24 V, -24 V, +6 V DC
Digital Audio Signal Reference Level -20 dBFS
Frequency Response 20 – 20,000 Hz, +1, -3 dB
Total Harmonic Distortion 0.008% (at 22 kHz LPF, 1 kHz, +10 dB(*1) output)
S/N Ratio At Input short, 20 – 20,000 Hz, set to ALL FLAT or OFF setting
Output volume min.: 90 dB
Output volume max.: 61 dB (Input 1 volume: 0 dB, Other Inputs: OFF)
Cross Talk Over 64 dB (at 20 kHz)
Tone Control Bass: ±12 dB (at 100 Hz)
Treble: ±12 dB (at 10 kHz)
Parametric Equalizer 10 bands, Frequency: 20 – 20,000 Hz, 31 steps, Variable range: ±12 dB, Q: 0.3 – 5
Speaker Equalizer 15 (compatible with TOA speakers only)
High-pass Filter -12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps
Low-pass Filter -12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps
Compressor Depth: 1 – 5
Delay 0 – 40 ms (1 ms steps), maximum 40 ms (CH 1 + CH 2), mixer mode only
Scene/Event Memory 32
Operation Mode Matrix mode/Mixer mode (selector switch)
Auxiliary Function Key lock function
Control Input/Output RS-232C(*2), D-sub connector (9 P, female)
Control input: 4 inputs, no-voltage make contact input, open voltage: 3.3 V DC,
short-circuit current: Under 1 mA, removable terminal block (14 pins)
Control output: 4 outputs, open collector output, withstand voltage: 27 V DC,
control current: 50 mA, removable terminal block (14 pins)
Remote volume: 2 channels, connect a 10 kΩ/linear taper variable resistor or
input the DC voltage of 0 to +10 V, removable terminal block (14 pins)
Operating Temperature -10℃ to +40℃
Operating Humidity 35% to 80% RH (no condensation)
Finish Panel: Aluminum, hair-line, black
Case: Surface-treated steel plate, black, paint
Dimensions 420 (W) × 107.6 (H) × 353 (D) mm
Weight 6 kg
Accessory Power cord (2 m) …1, Rack mounting bracket …2, Bracket mounting screw …4, Blank panel …7, Blank panel mounting screw …14,Removable terminal plug (3 pins) …2, Removable terminal plug (14 pins) …1,CD-ROM …1, Start guide …1

(*1) 0 dB = 1 V
(*2) Allowing it to be controlled by a control system such as AMX and Crestron through RS-232C port.

Digital Mixing Processor Unit

Digital Mixing Processor Unit

TOA D-2008SP

  The D-2008SP Digital Mixing Processor Unit is designed to have up to 32 audio inputs and outputs in total, and to be mounted in an EIA standard equipment rack (3U size). A built-in powerful signal processing function permits the unit to be used as both a mixer and a signal processor. Its audio input/output and control ports can accept optional plug-in modules, making the unit have a maximum of 32 inputs or 32 outputs and up to 2 control modules.

Using the following optional modules enables the unit to perform their functions: Two D-983s for providing a maximum of 48 contact inputs and 32 contact outputs, D-984VC for VCA control, and D-2000CB for audio data transfer between multiple D-2008SP units. Each function is set by the dedicated setting software on a PC. Setting contents can be stored in the unit’s internal memory as preset memory, which can be recalled by the D-2008SP without using a PC. The D-2012C, when connected, remotely controls the D-2008SP’s basic operations such as volume control.

Specifications

Power Source 220 – 240 V AC, 50/60 Hz
Power Consumption 76 W
Frequency Response 20 Hz – 20 kHz, ±1 dB (+4 dB* input)
Sampling Frequency 48 kHz
Input and Output Input: Max. 32 channels, modular construction (modules optional)
Output: Max. 32 channels, modular construction (modules optional)
Monitor bus: 1 stereo input, 1 stereo output
Connector: RJ45 connector
Connection cable: Shielded Category 5 or higher twisted pair
LAN cable(CAT5-STP)
Maximum cable distance: 100 m (between D-2008SP and D-2012C)
Headphone: 1 stereo

Signal Processing

Feedback Suppression Function 12 filters (auto + dynamic), maximum 4 bus channels
Auto-Mixing Function Ducker (automatic muting), NOM attenuation
Auto-Mixing Group 4 groups
Equalizer/Filter Parametric equalizer: 20 Hz – 20 kHz, ±15 dB, Q: 0.267-69.249
Filtering: High-pass filter 20 Hz – 20 kHz, 6 dB/oct, 12 dB/oct
Low-pass filter 20 Hz – 20 kHz, 6 dB/oct, 12 dB/oct
Notch filter 20 Hz – 20 kHz, Q: 8.651 – 69.249
All-pass filter 20 Hz – 20 kHz, Q: 0.267 – 69.249
High shelving filter 6 – 20 kHz, ±15 dB
Low shelving filter 20 – 500 Hz, ±15 dB
Horn equalizer 20 kHz, 0 to +18 dB (0.5 dB steps)
Crossover filter: 20 Hz – 20 kHz,
6 dB/oct, 12 dB/oct, 18 dB/oct, 24 dB/oct
Compressor/Auto-Leveler (Compressor mode)
Threshold: -20 to +20 dB (1 dB steps)
Ratio: 1:1, 1.1:1, 1.2:1, 1.3:1, 1.5:1, 1.7:1, 2:1, 2.3:1, 2.6:1, 3:1, 4:1,
5:1, 7:1, 8:1, 10:1, 12:1, 20:1, :1
Attack time: 0.2 ms – 5 s, Release time: 10 ms – 5 s
Gain: – – +10 dB
Knee type: hard knee, soft knee 1, soft knee 2
(Auto-leveler mode)
Target level: -20 to +10 dB (1 dB steps)
Maximum gain: 0 to +20 dB (1 dB steps)
Attack time: 10 ms – 10 s, Release time: 100 ms – 10 s
Output Delay Delay time: 0 – 1360 ms (0.021 ms steps)
BUS Delay Delay time: 0 – 677 ms (0.021 ms steps)
Matrix Input: Max. 34 ( 32 + 2 ) channels × 24 buses,
Output: Max. 44 (24 + 4 + 16) buses × 32 channels
CobraNet Matrix Input: Max. 16 channels × 24 buses,
Output: Max. 28 (24 + 4) buses × 16 channels
Crosspoint Gain – – 0 dB (1 dB steps)
Preset Memory 32
Auxiliary Function Key Locking function
LAN Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
Connected via a switching hub
Network protocol: TCP/IP
Connection cable: Shielded Category 5 or higher twisted pair LAN cable(CAT5-STP)
Maximum cable distance: 100m(between D-2008SP and switching hub)
Control RS-232C: D-sub connector (9 pins) Used for external control
Module: Remote control module slot: 2
Operating Temperature +5 ℃ to +40 ℃ (41 ゜F to 104 ゜F)
Finish Panel: Aluminum, hair-line finish, black Case: Surface-treated steel plate
Dimensions 482 (W) × 132.6 (H) × 343.4 (D) mm (18.98″ × 5.22″ × 13.52″)
Weight 6.3 kg (13.89 lb)
Accessory Power cord (2 m (6.5 ft)) …1, Rack mounting screw …4, CD (Set-up software) …1
Module mounting screw (spare) …4, Blank panel (preinstalled on the module slot) …8
Option Mic/line input module: D-2000AD1, D-921E, D-921F, D-922E, D-922F
Stereo select input module: D-936R
Digital input module: D-923AE, D-937SP
Line output module: D-971E, D-971M, D-971R, D-2000DA1
Digital output module: D-961SP, D-972AE
CobraNet interface module: D-2000CB
Remote control module: D-981, D-983
VCA control module: D-984VC

* 0 dB = 0.775 V

D-2012CD-2012C

  The D-2012C is a 6U rack mountable Remote Console Unit designed for exclusive use with the D-2008SP Digital Mixing Processor Unit. Assigned to any desired channels inside the D-2008SP by the dedicated software, the D-2012C’s 12 motorized faders and 8 rotary encoders can remotely adjust their volumes. Desired preset memories can be recalled using 8 function keys.

It is equipped with 1 channel line input (stereo), which allows the audio signal to be transmitted to the D-2008SP via monitor bus. Audio signals inside the D-2008SP can be monitored via monitor bus through headphones connected to a stereo headphone output. The D-2012C can be installed on a desk with the additional use of an optional D-2012AS Console Case.

Specifications

Power Source 220 – 240 V AC
Power Consumption 18 W
Volume Adjustment 100 mm motorized fader x 12
Rotary encoder x 8
Line Input 1 channel (stereo)
Headphone Output Stereo 100 mW + 100 mW (32 Ω load)
Monitor Bus 1 stereo input
Connector: RJ45 connector
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable (2 pairs of data lines)
Maximum cable distance: 100 m (109.36 yd) (between D-2012C and D-2008SP)
LAN Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
RJ45 connector
Network protocol: TCP/IP
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable
Maximum cable distance: 100 m (109.36 yd) (between D-2008SP and switching hub)
Control RS-232C: D-sub connector (9 pins) for maintenance use
Finish Panel: Surface-treated steel plate
Rack mounting bracket: Surface-treated steel plate
Dimensions 482 (W) × 266 (H) × 138 (D) mm (18.98 × 10.47″ × 5.43)
Weight 6.6 kg (14.55 lb)
Accessory Power cord (2 m (6.5 ft)) ……1
Fader knob (yellow) ……3
Option Console case: D-2012AS
4-channel Microphone/Line Input Module

4-channel Microphone/Line Input Module

D-2000AD1

  The D-2000AD1 is a 4-channel Microphone/Line Input Module designed for use with the D-2008SP Digital Mixing Processor Unit. It employs XLR type connectors.

Specifications

Input 4 channels, Mic/Line selectable
Mic: -50/-36 dB*, 2.6 kΩ, electronically-balanced
Line: -10 dB*, 2.6 kΩ/+4 dB*, 7 kΩ, electronically-balanced
Connector: XLR-3-31 equivalent
Phantom power supply (48 V DC, can be used when set for the Mic)
Ground lift switch
A/D Converter 24 bit
Sampling Frequency 48 kHz
Frequency Response 20 Hz – 20 kHz, ±1 dB (+4 dB* input)
Dynamic Range 104 dB (IHF-A weighted) or more (+4 dB* input)
Total Harmonic Distortion 0.008 % or less (+4 dB* input)
Finish Panel: Pre-coated steel plate, black, 30 % gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm (1.38″ × 4.7″ × 7.02″)
Weight 200 g (0.44 lb)
2-channel microphone/line input module

2-channel microphone/line input module

D-921E

The D-921E is a 2-channel microphone/line input module designed for use with the D-901 Digital Mixer, etc. It is equipped with removable terminal block type connectors. Input sensitivity and phantom power setting can be performed at the main frame such as the D-901.

Specifications

Input 2 channels, Mic/Line changeable
Mic: -50/-36 dB*, 4.7 kΩ, electronically-balanced,
removable terminal block (3 pins)
Line: -10/+4 dB*, 10 kΩ, electronically-balanced,
removable terminal block (3 pins)
Phantom power supply (can be used when set for the microphone)
15 V: D-901 (option), DP-K1 (option), D-2008SP (option)
12 V: SX-2100AI (option)
Ground lift switch
A/D Converter 24 bit
Sampling Frequency 48 kHz
Frequency Response 20 Hz – 20 kHz, ±1 dB (+4 dB* input)
Dynamic Range 100 dB (IHF-A weighted) or more (+4 dB* input)
Total Harmonic 
Distortion
0.05 % or less (+4 dB* input)
Finish Panel: Pre-coated steel plate, black, 30 % gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 140 g
Accessory Removable terminal plug (3 pins, preinstalled on the unit) …2
2-channel microphone/line input module

2-channel microphone/line input module

D-921F

  The D-921F is a 2-channel microphone/line input module designed for use with the D-901 Digital Mixer, etc. It is equipped with XLR connectors. Input sensitivity and phantom power setting can be performed at the main frame such as the D-901.

Specifications

Input 2 channels, Mic/Line changeable
Mic: -50/-36 dB*, 4.7 kΩ, electronically-balanced,
equivalent to XLR-3-31 type
Line: -10/+4 dB*, 10 kΩ, electronically-balanced,
equivalent to XLR-3-31 type
Phantom power supply (can be used when set for the microphone)
15 V: D-901 (option), DP-K1 (option), D-2008SP (option)
12 V: SX-2100AI (option)
Ground lift switch
A/D Converter 24 bit
Sampling Frequency 48 kHz
Frequency Response 20 Hz – 20 kHz, ±1 dB (+4 dB* input)
Dynamic Range 100 dB (IHF-A weighted) or more (+4 dB* input)
Total Harmonic 
Distortion
0.05 % or less (+4 dB* input)
Finish Panel: Pre-coated steel plate, black, 30 % gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 150 g
2-channel microphone/line input module

2-channel microphone/line input module

D-922E

  The D-922E is a 2-channel microphone/line input module designed for use with the D-901 Digital Mixer, etc. It is equipped with removable terminal block type connectors. The D-901’s 4-pole DIP switch is used to set the input sensitivity, phantom power supply, and ground lifting.

Specifications

Input 2 channels, -50/-36/-10/+4 dB* (Selectable with the DIP switch.),
4.7 kΩ, electronically-balanced, removable terminal block (3 pins)
Phantom power supply (can be set with the DIP switch)
15 V: D-901 (option), DP-K1 (option), D-2008SP (option)
12 V: SX-2100AI (option)
Ground lift switch (can be set with the DIP switch)
A/D Converter 20 bit
Sampling Frequency 48 kHz
Frequency Response 20 Hz – 20 kHz, ±1 dB (+4 dB* input)
Dynamic Range 85 dB (IHF-A weighted) or more (+4 dB* input)
Total Harmonic 
Distortion
0.2 % or less (+4 dB* input)
Finish Panel: Pre-coated steel plate, black, 30 % gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 125 g
Accessory Removable terminal plug (3 pins, preinstalled on the unit) …2

* 0 dB = 0.775 V

2-channel microphone/line input module

2-channel microphone/line input module

D-922F

  The D-922F is a 2-channel microphone/line input module designed for use with the D-901 Digital Mixer, etc. It is equipped with XLR connectors. The D-901’s 4-pole DIP switch is used to set the input sensitivity, phantom power supply, and ground lifting.

Specifications

Input 2 channels, -50/-36/-10/+4 dB* (Selectable with the DIP switch.),
4.7 kΩ, electronically-balanced, equivalent to XLR-3-31 type
Phantom power supply (can be set with the DIP switch)
15 V: D-901 (option), DP-K1 (option), D-2008SP (option)
12 V: SX-2100AI (option)
Ground lift switch (can be set with the DIP switch)
A/D Converter 20 bit
Sampling Frequency 48 kHz
Frequency Response 20 Hz – 20 kHz, ±1 dB (+4 dB* input)
Dynamic Range 85 dB (IHF-A weighted) or more (+4 dB* input)
Total Harmonic 
Distortion
0.2 % or less (+4 dB* input)
Finish Panel: Pre-coated steel plate, black, 30 % gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 135 g

LINE OUTPUT MODULE

Line Output Module

Line Output Module

D-2000DA1

The D-2000DA1 Line Output Module is designed for use with the D-2008SP Digital Mixing Processor Unit and features high quality sound. The output level of each output terminal can be independently set to either +4 dB or -10 dB and its output mode independently set to either balanced or unbalanced type by the built-in DIP switch. It employs XLR type connectors.

Specifications

Output 4 channels, +4 dB*/-10 dB* (changeable), adaptable load of 600 Ω or more,
balanced (electronically-balanced)/unbalanced (changeable), XLR-3-32 equivalent
D/A Converter 24 bit
Sampling Frequency 48 kHz
Frequency Response 20 Hz – 20 kHz, ±1 dB
Dynamic Range 104 dB (IHF-A weighted) or more
Total Harmonic 
Distortion
0.008 % or less
Finish Panel: Pre-coated steel plate, black, 30 % gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm (1.38″ × 4.7″ × 7.02″)
Weight 200 g (0.44 lb)
D-971E 4-channel line output module

D-971E 4-channel line output module

D-971E

The D-971E is a 4-channel line output module designed for use with the D-901 Digital Mixer, etc. It is equipped with removable terminal block type connectors.

Specifications

Output 4 channels, +4 dB*, adaptable load of over 600 Ω,
electronically-balanced, removable terminal block (3 pins)
D/A Converter 24 bits
Sampling Frequency 48 kHz
Frequency Response 20 – 20,000 Hz, ±1 dB
Dynamic Range Over 100 dB (IHF-A weighted)
Total Harmonic 
Distortion
Under 0.05%
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 140 g
Accessory Removable terminal plug (3 pins, preinstalled on the unit) …4
4-channel line output module

4-channel line output module

D-971M

The D-971M is a 4-channel line output module designed for use with the D-901 Digital Mixer, etc. It is equipped with XLR connectors.
Specifications

Output 4 channels, +4 dB*, adaptable load of over 600 Ω,
electronically-balanced, equivalent to XLR-3-32 type
D/A Converter 24 bits
Sampling Frequency 48 kHz
Frequency Response 20 – 20,000 Hz, ±1 dB
Dynamic Range Over 100 dB (IHF-A weighted)
Total Harmonic 
Distortion
Under 0.05%
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 165 g
4-channel line output module

4-channel line output module

D-971R

The D-971R is a 4-channel line output module designed for use with the D-901 Digital Mixer, etc. It is equipped with standard RCA pin jacks.

Specifications

Output 4 channels (2 outputs for each channel), -10 dB*,
adaptable load of over 600 Ω, RCA pin jack
D/A Converter 24 bits
Sampling Frequency 48 kHz
Frequency Response 20 – 20,000 Hz, ±1 dB
Dynamic Range Over 100 dB (IHF-A weighted)
Total Harmonic 
Distortion
Under 0.05%
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 150 g
Cobranet Interface Module

Cobranet Interface Module

D-2000CB

 The D-2000CB is designed for use with the D-2008SP Digital Mixing Processor Unit. When mounted to the D-2008SP, it allows audio transmission between this D-2008SP and other one. Each function is set by the dedicated setting software on a PC.

Specifications

Network I/F CobraNet: 100BASE-TX, PRIMARY/SECONDARY 2 system,
RJ45 connector, Enables decentralized installation, Audio transmission only
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable
To be connected via the specified switching hub
Note: This network should be completely independent of other LAN.
Number of D-2008SP connection: Max. 4
Switching hub stage: Max. 7
Max extend distance: 100m (328.1 ft) (connected via a switching hub)
Input 16 channels, 20 bit/24 bit
Output 16 channels, 20 bit/24 bit
Sampling Frequency 48 kHz
Finish Panel: Pre-coated steel plate
Dimensions 17 (W) × 80 (H) × 140 (D) mm (0.67″ × 3.15″ × 5.51″) (excluding projection)
Weight 100 g (0.22 lb)
Accessory Panel …1, Screw …3
VCA fader unit

VCA fader unit

D-911

  The D-911 is a dedicated VCA fader unit designed for use with the D-901 Digital Mixer, etc. Connecting the D-911 to the D-984VC, VCA control module permits the volume control of all channels and contact controls.

Specifications

Power Supply 5 V DC (supplied from the optional D-984VC)
Connector RJ45 connector × 8
Input Fader Control Input fader (100 mm) × 12
Output Volume Control Output volume control × 8
Contact Control Illuminated switch × 8
Remote Output No-voltage make contact output (contact capacity: 30 V DC, 4 A)
Remote Switch Seesaw switch for activating the remote function of the power distributor
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 482.6 (W) × 177 (H) × 61.3 (D) mm (excluding projection)
Weight 2.7 kg
Accessory Fader knob (Red, Yellow)…3 each, Volume knob (Red)…2,
Rack mounting screw…4, Rack mounting bracket (preinstalled on the unit)…2

DIGITAL INPUT MODULE

2-channel line digital input module

2-channel line digital input module

D-923AE

  The D-923AE is a 2-channel line digital input module designed for use with the D-901 Digital Mixer, etc. With the use of this module, digital signals can be input, permitting direct connection of the D-901 Digital Mixer to equipment having a digital output. Owing to the built-in sample rate converter, the module can handle signals of various sampling frequencies.

Specifications

Input 2 channels, 2.0 – 7.0 V (p-p), 110 Ω, XLR-3-31 or equivalent
Applicable Format AES/EBU (2 channel multiplexed)
Sampling Frequency 32 – 48 kHz
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 130 g
1 stereo channel line digital input module

1 stereo channel line digital input module

D-937SP

  The D-937SP is a 1 stereo channel line digital input module designed for use with the D-901 Digital Mixer, etc. With the use of this module, digital signals can be input, permitting direct connection of the D-901 Digital Mixer to equipment having a digital output. Owing to the built-in sample rate converter, the module can handle signals of various sampling frequencies. When this module is used, one of four stereo inputs is selected for output to the D-901. Input selection can be performed at the front panel, by PC software or through a remote control module.

Specifications

Input Stereo 1 channel line (Selectable one of four inputs)
0.5 V (p-p), 75 Ω, Coaxial RCA jack × 2
Square optical connector × 2
Applicable Format S/PDIF (2 channel multiplexed)
Sampling Frequency 32 – 48 kHz
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 130 g
D-936R 4 stereo input module

D-936R 4 stereo input module

D-936R

The D-936R is a 4 stereo input module designed for use with the D-901 Digital Mixer, etc. It is equipped with standard RCA pin jacks. The D-936R features two stereo transmission modes: 1)Selection of one of the four stereo inputs for transmission to the D-901. 2)Mixing of all four stereo inputs, transmitting the mixed signal to the D-901 through left/right channel outputs. Mode settings and stereo selection are performed at the main frame such as the D-901.
Specifications

Input 1) When the module is attached to the D-901 (option) or D-2008SP (option)
or DP-K1 (option); stereo × 4 inputs (Selection of 1 stereo or mixing or
all 4 stereo inputs) -10 dB*, 10 kΩ, RCA pin jack
2) When the module is attached to the SX-2100AI (option);
monaural × 2, -10 dB*, 10 kΩ, RCA pin jack
A/D Converter 24 bit
Sampling Frequency 48 kHz
Frequency Response 20 Hz – 20 kHz, ±1 dB (+4 dB* input)
Dynamic Range 100 dB (IHF-A weighted) or more
Total Harmonic 
Distortion
0.05 % or less
Finish Panel: Pre-coated steel plate, black, 30 % gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 145 g
Stereo 2-channel line digital output module

Stereo 2-channel line digital output module

D-961SP

  The D-961SP is a Stereo 2-channel line digital output module designed for use with the D-901 Digital Mixer, etc. With the use of this module, digital signals can be output, permitting direct connection of the D-901 Digital Mixer to equipment having a digital input. Each pair of optical output and coaxial output is output in parallel.
Specifications

Output: Stereo 2 channel line (with splitter, can be output to each pair of
optical output and coaxial output in Parallel),
0.5 V (p-p) 75 Ω, Coaxial RCA jack × 2,
Square optical connector × 2
Applicable Format S/PDIF (2 channel multiplexed)
Sampling Frequency 48 kHz
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 130 g

D-972AE

The D-972AE is a 4-channel line digital output module designed for use with the D-901 Digital Mixer, etc. With the use of this module, digital signals can be output, permitting direct connection of the D-901 Digital Mixer to equipment having a digital input.

Specifications

Output 4 channels, 5.0 V (p-p), 110 Ω, XLR-3-32 or equivalent × 2
Applicable Format AES/EBU (2 channel multiplexed)
Sampling Frequency 48 kHz
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 130 g
Accessory Ferrite clamp…2
 remote control module

remote control module

D-981

   The D-981 is a remote control module designed for use with the D-901 Digital Mixer, etc. It permits preset memory recall, input/output channel volume control, stereo input selection and channel ON/OFF operation to be remotely controlled from external equipment. Tally output can also be provided for external control.

Specifications

Contact Input COM + Terminals 1 – 8: Open voltage: 5 V DC, short-circuit current: 5 mA
removable terminal block (10 pins)

Control

Preset Memory 
Selection
Any preset memory can be recalled.
Control method: No-voltage make of over 100 ms/
Volume Control Any input/output channel volume can be turned UP or Down.
Control method: 1 step variation for no-voltage make single pulse of over 100 ms
1 step continuous operation for every 70 ms for
no-voltage make of over 100ms. Can be reset when at break.
Variable range : -∞ dB to +10 dB
Channel Any input/output channel can be turned ON and OFF.
Control method: No-voltage make of over 100 ms/
no-voltage make single pulse of over 100 ms
Stereo Selection Input channel lines of the D-936R (optional), or the D-937SP (optional)
(4 stereo input module) can be selected.
Control method: No-voltage make of over 100 ms/
No-voltage make single pulse of over 100 ms
Contact Output COM + Terminals 1 – 8: No-voltage make contact input,
contact capacity: 24 V DC, 100 mA
removable terminal block (10 pins)
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 125 g
Accessory Removable terminal plug (10 pins, preinstalled on the unit) …2
remote control module

remote control module

D-983

The D-983 is a remote control module designed for used with the D-901 Digital Mixer, etc. It permits preset memory recall, input/output channel volume control, stereo input selection and channel ON/OFF operation to be remotely controlled from external equipment. Tally output can also be provided for external control.
Specifications

Contact Input COM + Terminal 1 – 24: Open voltage: 5 V DC,
short-circuit current: 5 mA, RJ45 connector × 4

Control

Preset Memory 
Selection
Any preset memory can be recalled.
Control method: No-voltage make of over 100 ms/
No-voltage make single pulse of over 100 ms
Volume Control Any input/output channel volume can be turned UP or DOWN.
Control method: 1 step variation for no-voltage make single pulse of over 100 ms
1 step continuous operation for every 70ms for no-voltage
make of over 100ms. Can be reset when at break.
Variable Range: -∞ dB to +10 dB
Channel Any input/output channel can be turned ON and OFF.
Control method: No-voltage make of over 100 ms/
No-voltage make single pulse of over 100 ms
Stereo Selection Input channel lines of the D-936R (optional), or the D-937SP
(optional) (4 stereo input module) can be selected.
Control method: No-voltage make of over 100 ms/
No-voltage make single pulse of over 100 ms
Contact Output COM + Terminals 1 – 16: No-voltage make contact,
contact capacity: 24 V DC, 100 mA,
RJ45 connector × 4
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 170 g
D-984VC VCA control module

D-984VC VCA control module

D-984VC

The D-984VC is a dedicated VCA control module designed for use with the D-901 Digital Mixer. It expands the D-901 Digital Mixer’s functions by 20 VCA control inputs, 8 contact inputs, and 8 contact outputs. By the VCA controls from external equipment, this module permits the D-901’s gains of 12 inputs and 8 outputs to be controlled. By the contact input controls from external equipment, this module permits the preset memory recall, input/output channel gains, stereo input selection, and channel ON/OFF to be controlled. By the contact output controls Tally outputs can also be provided for external control.

Specifications

VCA Control Input +5 V, GND, Terminal 1 – 20 (12 Input channels, 8 output channels),
RJ45 connector × 4
Control contents: Volume control of each input/output channel
Variable range: – dB to + 0 dB
Contact Input COM + Terminal 1 – 8: Open voltage: 5 V DC,
short-circuit current: 5 mA, RJ45 connector × 2

Control

Preset Memory 
Selection
Any preset memory can be recalled.
Control method: No-voltage make of over 100 ms/
No-voltage make single pulse of over 100 ms
Volume Control Any input/output channel volume can be turned UP or DOWN.
Control method: 1 step variation for no-voltage make single pulse of
over 100 ms
1 step continuous operation for every 70ms for no-voltage
make of over 100ms. Can be reset when at break.
Variable Range: – dB to +10 dB
Channel Any input/output channel can be turned ON and OFF.
Control method: No-voltage make of over 100 ms/
No-voltage make single pulse of over 100 ms
Stereo Selection Input channel lines of the D-936R (optional), or the D-937SP
(optional) (4 stereo input module) can be selected.
Control method: No-voltage make of over 100 ms/
No-voltage make single pulse of over 100 ms
Contact Output COM + Terminal 1 – 8: No-voltage make contact,
contact capacity: 24 V DC, 100 mA,
RJ45 connector × 2
Finish Panel: Pre-coated steel plate, black, 30% gloss
Dimensions 35 (W) × 119.5 (H) × 178.4 (D) mm
Weight 170 g

supplier aiphone

 

JM-4MED
JM-4MEDHands-free color video intercom master station
The JM Series features a large 7-inch touchscreen monitor for clear visitor identification and easy operation control.
The JM Series can be installed at 4 door locations and connected to 8 inside locations with internal communication between stations.

 

Features

  •          7-inch wide touch screen for operation
  •          Hands-free or handset audio communication
  •          Room-to-room communication is available.
  •          Instant voice call-in with image
  •          Zoom/wide and Pantilt video control
  •          Camera position preset
  •          Backlight compensation by “IMAGE” button
  •          Visual monitoring with audio is available
  •          Full color video in low light situations (even at night) without external illumination.
  •          Record visitor images both automatically & manually to internal memory or SD/SDHC card (not included)
  •          White LED illumination turns on in low-light conditions
  •          Vandal resistant video door station
  •          3 wiring methods selectable:
    Station-to station, Homerun(*), or combined wiring(*)
    (*) by using JM-8Z distribution adaptor
  •          Audio monitoring of other master stations
  •          Option: 3 sensors connectable to the master station
  •          Maximum distance can reach 300m between the door and master station by using JMW-BA adaptor.
  •          CCTV is connectable by using JMW-BA adaptor.
  •          Available in multiple languages

 

 

gtThe GT Series provides building complexes with high performance security & usability. A variety of models adapt to almost any type of building.
Wide and Zoom & PanTilt Panoramic Wide Angle View

 

  •          To provide effective security, the GT series features a wide angle camera that enables you to see an innovative panoramic view! People standing on sides and people of all heights can be easily identified.

Zoom

  •          To see details, switch to Zoom mode. Switching between Wide and Zoom mode can be done by the press of a button.

PanTilt

  •          PanTilt is available to change the camera angle in Zoom mode.

Picture Memory

Automatic Recording

  •          Works anytime, even during your absence. Records 6 images per picture sequence. Up to 40 pictures sequences can be recorded.

Manual Recording

  •          Record picture as required. The recording starts when you press the REC button while monitoring or talking to a visitor.

Playing

  •          The play LED flashes when there are auto-recorded pictures.Press the PLAY button to play.

Additional Security

  •          The Master Station with the recording function can be connected with 3 security lines. It can also be connected with an emergency button. When sensing an input from the button, the alarm will be triggered after the set time.

High Degree of Usability for Visitors

Audio & Visual Guidance

  •          The Entrance Station features both audio and visual guidance, so any visitor knows the present situation. The audio guide is available in 6 languages (English, French, German, Spanish, Dutch, and Italian).

Catalog(3.24MB) : http://www.aiphone.net/product/multi/gt_st/image/catalog.pdf

untuk informasi dan pemesanan silahkan menghubungi kami di 08568420133 081389467537 / email : admin@mitramandiriselaras.co.id atau kunjungi website kami di www.mitramandiriselaras.co.id

SUPPLIER ELECTRONIC

MITRA MANDIRI SELARAS. CV
M/E CONTRACTOR, HOME BUILDER, MAINTENANCE AND SUPPLIES

adalah perusahaan yang bergerak dalam bidang mechanical and Electrical Contractor, maintenance and supply yang meliputi pekerjaan 

·         Fire alarm system
·         fire hydrant & sprinkler system
·         sound & paging system
·         telecomunication system
·         matv & cctv system
·         audio and video intercom system
·         fm-200
·         air conditioning system
·         Home builder
·         Property
 
Kami mengerjakan Instalasi dan pemasangan untuk semua system elektrikal dan elektronik untuk proyek apartement, gedung perkantoran, rumah sakit, pabrik/ gudan, perumahan, serta rumah tinggal dengan mengutamakan kualitas, target schedule dan harga kompetitif.
 
Perusahaan kami senantiasa selalu menjalin hubungan baik dengan semua klien untuk terciptanya kerukunan serta kesinambungan dan prospek yang lebih baik dalam kancah industry konstruksi dan elektronika nasional dengan tetap konsisten dan dedikasi tingggi dalam berkarya.
 
kami jmenyediakan segala kebutuhan elektronik untuk kebutuhan industri dan umum lainnya dengan merek : TOA-NITTAN-NOHMI-HOOSEKI-PANASONIC-OZEKI-APPRON-SMARTFIRE-KIDDE-BOSCH-SAMSUNG-IRCO-DLLAIPHONE, TOA, NITTAN, NOHMI, HOOSEKI, PANASONIC, OZEKI, APPRON, SMARTFIRE, KIDDE, BOSCH, SAMSUNG, IRCO
 

untuk informasi dan pemesanan silahkan menghubungi kami di 08568420133 081389467537 / email : bandi.mms@gmail.com atau kunjungi website kami di www.mitramandiriselaras.com

Nurse call

NEM-20MITRA MANDIRI SELARAS. CV

adalah perusahaan yang bergerak dalam bidang mechanical and Electrical Contractor, maintenance and supply yang meliputi pekerjaan :
Fire alarm system, fire hydrant & sprinkler system, sound & paging system, telecomunication system, matv & cctv system,Nurse call system, audio and video intercom system, fm-200 system
Peralatan yang kami supply dan kerjakan untuk nurse call system/ panggilan perawat pada rumah sakit/ instansi kesehatan swasta atau pemerintah adalah merek AIPHONE Segala kebutuhan untuk peralatan nurse call sytem tersedia lengkap antara lain : NEM-10 s/d NEM-60, NHX, NBR-8A,NBR-7AS, NBY-1A, NBY-4A, NB-L, NAR-2A, NAR-6A, Zone module dll

 

kami juga menyediakan kebutuhan kebutuhan elektronik lainnya dengan merek : AIPHONE-BOSCH-TOA-NITTAN-NOHMI-HOOSEKI-KIDDE-SAMSUNG-IRCO-IKUSI-YUN YANG

untuk info produk, layanan, harga  dan pemesanan silahkan menghubungi kami
di  08568420133 081389467537 / email : admin@mitramandiriselaras.co.id 
atau kunjungi website kami di www.mitramandiriselaras.co.id
atau http://bandimms.wix.com/mitramandiriselaras

contractor and electronic supplier

MITRA MANDIRI SELARAS

M/E CONTRACTOR, HOME BUILDER, MAINTENANCE AND SUPPLIES
jl. jatijajar II no. 9 Tapos-Depok Jawa barat 16955
Indonesia
Scoop of work :
– Fire alarm system
– fire hydrant and sprinkler
– Sound and paging system
– Telephone & Data system
– MATV and CCTV system
– Nurse call system
– Apartment system (audio & video )
– FM-200
– Air conditioning system
Maintenance :
– Fire alarm system
– fire hydrant and sprinkler
– Apartment system (audio & video )
– FM-200
– Air conditioning system (split only)
Supplies :
– Aiphone
– Toa
– Bosch
– Yun yang
– Nittan
– Hooseki
– Nohmi
– Kidde
– IRCO 
other :
– home builder
– renovation
– property agent electronic supplier

untuk info produk, layanan, harga  dan pemesanan silahkan menghubungi kami
di  08568420133 081389467537 / email : admin@mitramandiriselaras.co.id 
atau kunjungi website kami di www.mitramandiriselaras.co.id

aiphone

MITRA MANDIRI SELARAS CV

Mechanical, Electrical and plumbing (design, instalation and supplies)

Our job list :
– fire alarn, fire hydrant & sprinkler
– telecomunication and data system
– cctv & smatv
– access card
– paging system,
– audio and video intercom system (apartment system)
– nurse call system (hospital)
– air conditioning system
– fm-200 (data server)

supplies
– AIPHONE ( video intercom, video entry security and nurse call system )
– TOA ( paging system/ car call, and cctv system )
– BOSCH ( paging system/ car call, and cctv system )
– PANASONIC ( telecomunication system )
– SAMSUNG ( paging system/ car call, cctv system and telecomunication system )
– SIEMENS ( addressable and Conventional fire alarm system )
– NITTAN ( addressable and Conventional fire alarm system )
– NOHMI ( addressable and Conventional fire alarm system )
– FIRELITE ( addressable and Conventional fire alarm system )
– HOOSEKI ( Fire hydrant, addressable and Conventional fire alarm system )
– APPRON ( Fire hydrant and Conventional fire alarm system )
– HOCHIKI (Conventional fire suppression system )
– KIDDE ( fm-200, addressable and Conventional fire suppression system )
– IRCO ( matv system )

Maintenance system
– Hospital
– Apatment
– Office building
– Factory

electronic supplier

MITRA MANDIRI SELARAS CV
ECHANICAL AND ELECTRICAL CONTRACTOR, MAINTENANCE AND SUPPLIES
Supplies :
– 

Slideshow ini membutuhkan JavaScript.

samsung DVR
fix colour camera
samsung doom camera
samsung fix colour camera
samsung doom camera
samsung colour camera
samsung colour camera
fixed colour camera
bosch fix colour camera
video door station flush mount type
audio intercom
ir colour camera
fix colour camera
p/t/z colour camera
conventional FA panel
Addressable FA panel for fm-200
p/t/z colour camera
samsung doom camera
pabx up to 100 line
bedside call switch
single vodeo door station
photo electric smoke detecto
fix colour camera
ror heat detector
intercom system
ceiling speaker
intercom system
standard pabx
master nurse call 20 chanel
video intercom system w/2 door station
door station ( audio only )
fix colour camera
fix colour camera
video intercom w/ memory
single video intercom
video intercom w/ picture memory
single video intercom
security guard station
colour door station
colour door station
master entrance
audio intercom
audio intercom
volume control
indicator light
doom colour camera
fix colour camera
doom colour camera
p/t/z colour camera
hydrant box indoor
fix heat detector
entrance station
p/t/z colour camera
volume control
manual push button
DVR
audio master intercom
hand set intercom
hand set intercom
fix colour camera
fix colour camera
fix colour camera
DVR
fix colour camera

other :
– home builder 
– renovation
– property agent 

contraktor

MITRA MANDIRI SELARAS CV

MITRA MANDIRI SELARAS CV
jl. jatijajar II no. 9 Tapos-Depok Jawa barat, Depok, Jawa Barat, 16955, Indonesia
Phone: 0.219.112.3972 – 7058.0976
Fax: 0.217.058.0978

M/E CONTRACTOR, MAINTENANCE AND SUPPLIES

Scoop of work :

Maintenance :
– Fire alarm system
– fire hydrant and sprinkler
– Sound system
– Telephone & Data system
– MATV and CCTV system
– Nurse call system
– Apartment system (audio & video )
– FM-200
– Air conditioning system

Supplies :
– Aiphone
– Toa
– Bosch
– Samsung
– Nittan
– Hooseki
– Nohmi
– Appron
– Siemens
– Smartfire
– Ozeki
– IRCO

other :
– home builder
– renovation

kami juga menyediakan kebutuhan kebutuhan elektronik lainnya dengan merek : AIPHONE-BOSCH-TOA-NITTAN-NOHMI-HOOSEKI-KIDDE-SAMSUNG-IRCO-IKUSI-YUN YANG

untuk info produk, layanan, harga  dan pemesanan silahkan menghubungi kami
di  08568420133 081389467537 / email : admin@mitramandiriselaras.co.id 
atau kunjungi website kami di www.mitramandiriselaras.co.id

home builder

type59-144_gambar rumah minimalis_cluster ifolia_harapan indah_bekasiMITRA MANDIRI SELARAS

adalah perusahaan yang bergerak dalam bidang mechanical and Electrical Contractor, maintenance, supplier dan home builder,

Kami mengerjakan, desain dan bangun rumah tinggal, ruko/ rukan, gudang dan sarana umum lainnya termasuk :

 

  • pembuatan dan pemasangan pagar,
  • pembuatan dan pemasangan trails,
  • pembuatan dan pemasangan railing tangga,
  • pemasangan canopy,
  • pemasangan rolling/ sliding door,
  • pemasangan rangka baja
  • pemasangan gypsum, dan keramik dll.

 

Kami Mengutamakan kualitas dan kepuasan klien dengan harga kompetitif, jaminan legalitas dan transparansi.

untuk informasi dan pemesanan silahkan menghubungi kami di 08170005563 –  081380221226 / email : bejoparyono@mitramandiriselaras.co.id atau kunjungi website kami di www.mitramandiriselaras.co.id untuk mendapatkan informasi lain mengenai kami

FM-200/fire suppression

MITRA MANDIRI SELARAS

adalah perusahaan yang bergerak dalam bidang mechanical and Electrical Contractor, maintenance and supply yang meliputi pekerjaan :

Electrical, Fire Hidrant dan sprinkler system, sound & paging system, telecomunication & data system, matv & cctv system intercom system, fire suppression system/ FM-200 serta air conditioning system

Peralatan yang kami supply dan kerjakan untuk , fire suppression system/ FM-200 dengan merek  KIDDE Kami menyediakan segala kebutuhan proteksi ruang server untuk gedung perkantoran, pabrik atau gudang/ware house. menyediakan aneka type panel control, detector, manual push button, sounder beacon,tabung/ cylinder,solenoid,dan berbagai asesories lainnya sesuai kebutuhan.

kami juga menyediakan kebutuhan kebutuhan elektronik lainnya dengan merek : AIPHONE-BOSCH-TOA-NITTAN-NOHMI-HOOSEKI-KIDDE-SAMSUNG-IRCO-IKUSI-YUN YANG

untuk info produk, layanan, harga  dan pemesanan silahkan menghubungi kami
di  08568420133 081389467537 / email : admin@mitramandiriselaras.co.id 
atau kunjungi website kami di www.mitramandiriselaras.co.id