PRODUK DAN JASA |
Mechanical and electrical contractor, maintenance and supply |
The WM-3210 Wireless Microphone employs a dynamic microphone capsule and is suitable for vocal applications. Thanks to the PLL-synthesizer system, 6 different operating frequencies are made available. A high output power ensures stable radio signal transmission.
Specifications
Microphone Element | Dynamic microphone unit: Cardioid |
Emission | F3E |
Frequency Range | 169 – 216 MHz, VHF |
Channel Selectable | 6 ch |
RF Carrier Power | Less than 50 mW |
Tone Frequency | 32.768 kHz |
Modulation System | PLL synthesizer |
Maximum Input Level | 125 dB SPL |
Maximum Deviation | ±40 kHz, ±15 kHz (ONLY US Part.90) |
Battery | 6LR61 (9 V × 1) |
Battery Life | 10 hours (alkaline) |
Indicator | Power/Battery indicator (common use) |
Antenna | Internal antenna |
Operating Temperature | -10℃ to +50℃ |
Finish | Resin, coating (change other’s) |
Dimensions | φ50 × 235.2 mm |
Weight | 250 g (with battery) |
Accessory | Stand adapter……1, Screw driver……1 |
The WM-3220 Wireless Microphone employs an electret condenser microphone capsule and is suitable for speech applications. Thanks to the PLL-synthesizer system, 6 different operating frequencies are made available. A high output power ensures stable radio signal transmission.
Specifications
Microphone Element | Electlet condenser unit: Cardioid |
Emission | F3E |
Frequency Range | 169 – 216 MHz, VHF |
Channel Selectable | 6 ch |
RF Carrier Power | Less than 50 mW |
Tone Frequency | 32.768 kHz |
Modulation System | PLL synthesizer |
Maximum Input Level | 120 dB SPL |
Maximum Deviation | ±40 kHz, ±15 kHz (ONLY US Part.90) |
Battery | 6LR61 (9 V × 1) |
Battery Life | 10 hours (alkaline) |
Indicator | Power/Battery indicator (common use) |
Antenna | Internal antenna |
Operating Temperature | -10℃ to +50℃ |
Finish | Resin, coating (change other’s) |
Dimensions | φ45 × 235.2 mm |
Weight | 250 g (with battery) |
Accessory | Stand adapter……1, Screw driver……1 |
The WM-3310 lavalier wireless microphone has been manufactured for use with a VHF system. It incorporates a cardioid pick-up pattern and has been designed for use in speech reinforcement applications. The built-in compressor-expander circuit minimizes the influence from ambient noise.
Specifications
Microphone | Electret condenser microphone, cardioid |
Emission | F3E |
Frequency Range | 169 – 216 MHz, VHF |
Channel Selectable | 6 ch |
RF Carrier Power | Less than 50 mW |
Tone Frequency | 32.768 kHz |
Modulation System | PLL synthesizer |
Maximum Input Level | 120 dB SPL |
Battery | 6LR61 (9 V × 1) |
Battery Life | 10 hours (alkaline) |
Indicator | Power/Battery indicator (common use) |
Antenna | 1/4 wire antenna |
Operating Temperature | -10℃ to +50℃ |
Finish | Resin, coating |
Dimensions | 62 |
Weight | 135 g (with battery) |
Accessory | Screw driver……1 |
.
The TOA wireless tuner WT-3800 is a PLL-synthesizer controlled double superheterodyne diversity tuner to be used in VHF wireless systems. It employs a compander noise reduction circuit to minimizes the influence of the ambient RF noise.
Specifications
Power Source | AC mains |
Power Consumption | 150 mA (13.8 V DC) |
Receiving Frequency | 169 – 216 MHz, VHF |
Channel Selectable | 6 ch |
Receiving System | Double super-heterodyne |
Diversity System | Space diversity |
Output | MIC: -60 dB*, 600 Ω, balanced, XLR-3-31 type connector LINE: -20 dB*, 600 Ω, unbalanced, phone jack MIC or LINE is selectable. |
Mixing Input | -20 dB*, 4 kΩ, unbalanced, phone jack |
Antenna Input | 75 Ω, BNC (phantom powering for antenna), 9 V DC, 30 mA (max) |
Receiving Sensitivity | Over 80 dB, S/N ratio (20 dBμV input, 40 kHz deviation) |
Squelch Sensitivity | 18 – 40 dBμV variable |
Squelch System | Using together of noise SQ, carrier SQ and tone SQ |
Tone Frequency | 32.768 kHz |
Indicator | CHANNEL, ANT A/B, Audio (peak, signal) |
Channel Check | Usable frequencies scanning |
S/N Ratio | Over 100 dB (A-weight, balanced output) |
Harmonic Distortion | Under 1% |
Frequency Response | 100 – 12,000 Hz, ±3 dB |
Other Function | Frequency select by PC, channel |
Operating Temperature | -10℃ to +50℃ |
Finish | Resin, black |
Dimensions | 210 |
Weight | 600 g |
Accessory | AC – DC adapter (230 V AC, 50 Hz)………1, |
Option | Mounting bracket kit: MB-WT3 (for rack mounting one WT-3800 unit) MB-WT4 (for rack mounting two WT-3800 units) |
TOA’s WT-3810 is a PLL-synthesizer controlled double superhetrodyne diversity tuner designed to be used with a VHF wireless system. It employs a compander noise reduction circuit to minimize the influence of ambient RF noise.
Specifications
Power Source | AC mains |
Power Consumption | 150 mA (13.8 V DC) |
Receiving Frequency | 169 – 216 MHz, VHF |
Channel Selectable | 6 ch |
Receiving System | Double super-heterodyne |
Diversity System | Space diversity |
Output | -20 dB*, 600 Ω, unbalanced, phone jack |
Mixing Input | -20 dB*, 4 kΩ, unbalanced, phone jack |
Antenna | Rod antenna |
Receiving Sensitivity | Better than 80 dB, S/N ratio (20 dBμV input, 40 kHz deviation) |
Squelch System | Using together of noise SQ and carrier SQ |
S/N Ratio | Better than 100 dB (A-weight, balanced output) |
Harmonic Distortion | Less than 1% |
Frequency Response | 100 – 12,000 Hz, ±3 dB |
Operating Temperature | -10℃ to +50℃ |
Finish | Resin, black |
Dimensions | 240 |
Weight | 380 g |
Accessory | AC – DC adapter (230 V AC, 50 Hz)…1, Driver for channel changing…1 |
Intended for 200 MHz band wireless systems, the YW-3500 is a wall-mounted dipole antenna. It has an internal band pass filter and a booster circuit, and is equipped with an operation LED.
Specifications
Power Source | 8 – 10 V DC (supplied from amplifier or tuner) |
Current Consumption | Under 24 mA |
Receiving Frequency | 168 – 216 MHz |
Dipole Ratio Relative Gain | 6 dB (including booster amplifier) |
V.S.W.R | Under 2.6 |
Output Impedance | 75 Ω |
Operating Temperature | -10%%dC to +50%%dC |
Mounting Hole Pitch | 68.5 mm (dimensions for wiring box) |
Finish | Antenna/bracket : ABS resin, off white |
Dimensions | 197 |
Weight | 200 g |
Accessory | Tapping screw (M4) for wooden wall……2, M3.5 screw for wiring box……2, RG-59/U sleeve……1 |
※ To minimize cable loss, use the RG-59/U or RG-6/U cable.
The YW-3510 is a 1/4 type antenna designed to be mounted directly to the wireless tuner. It can be used for both UHF and VHF bands by adjusting the length of its element.
Specifications
Receiving Frequency Range | VHF (longest): 169 – 216 MHz UHF (shortest): 690 – 865 MHz |
Antenna Gain | Approx. -3 dBd |
Output Impedance | 75 Ω |
Output Connector | BNC plug |
Finish | Antenna element: Chrome plated brass Other: Nickel-plated brass |
Dimensions | Antenna element length: (for VHF) 378 mm, (for UHF) 108 mm Maximum connector diameter: φ15 mm |
Weight | 27 g |
Integrated DSP & Control System
The DP-K1 is a 3U rack mountable Digital Audio Processor. It features an Automatic Resonance Control function that automatically generates an optimum filter curve to improve sound clarity after measuring the acoustic characteristics in architectural space. It permits flexible configuration of inputs and outputs, from 2-IN/4-OUT to 8-IN/8-OUT using the optional modules. Each function is set by a PC using the dedicated software. The settings can be stored in the unit’s internal memory and the stored preset memories can be recalled from the unit without connecting the PC.
Specifications
Power Source | 100 – 120 V AC, 50/60 Hz |
Power Consumption | 40 W (750 mA) |
Frequency Response | 20 – 20,000 Hz, ±1 dB (+4 dB* input) |
Input | Max. 8 channels, modular construction (modules optional) |
Output | Max. 8 channels, modular construction (modules optional) |
IO Configuration | 2-IN/4-OUT, 2-IN/8-OUT, 4-IN/4-OUT, 4-IN/8-OUT, 6-IN/4-OUT, 6-IN/8-OUT, 8-IN/4-OUT, 8-IN/8-OUT |
Signal Processing
Automatic Resonance Control Function |
Parametric equalizer: 20 – 20,000 Hz, ±12 dB, Q: 0.267 – 69.249 |
Level Control | – to +12 dB (0.5 dB steps), with polarity selector |
Equalizer/Filter | Parametric equalizer: 20 – 20,000 Hz, ±12 dB, Q: 0.267 – 69.249 Filtering: High-pass filter 20 – 20,000 Hz, 6 dB/oct, 12 dB/oct Low-pass filter 20 – 20,000 Hz, 6 dB/oct, 12 dB/oct Notch filter 20 – 20,000 Hz, Q: 8.651 – 69.249 All-pass filter 20 – 20,000 Hz, Q: 0.267 – 69.249 High shelving filter 6 – 20 kHz, ±12 dB Low shelving filter 20 – 500 Hz, ±12 dB Horn equalizer 20 kHz, 0 to +18 dB (0.5 dB steps) Crossover filter: 20 – 20,000 Hz, 6 dB/oct, 12 dB/oct, 18 dB/oct, 24 dB/oct |
Compressor | Threshold: -16 to +24 dB* (1 dB steps) Ratio: 1:1, 2:1, 3:1, 4:1, 8:1, 12:1, 20:1, :1 Attack time: 0.02 – 100 ms Release time: 10 ms – 5 s |
Noise gate | Threshold: – to -26 dB* (1 dB steps) Attack time: 0.1 – 100 ms Release time: 20 ms – 5 s |
Delay | Delay time: 0 – 682.0 ms (0.021 ms steps) |
Matrix | 8 × 8 Level control: – to 0 dB (1 dB steps), with polarity selector |
Preset Memory | 8 |
Auxiliary Function | Key lock function |
Setting Software | OS: Windows 2000/XP Control system: 10 BASE – T/100 BASE-TX, Auto-Negotiation, RJ45 connector |
Front Panel Section | Preset memory recall knob: 1 Input indicator: Green LED Output indicator: Green LED |
Module Slot (Rear Panel) |
Input module slot: 4 Output module slot: 2 Remote control module slot: 1 |
Operating Temperature | +5℃ to +40℃ |
Finish | Panel: Aluminum, hair-line finish, black Others: Pre-coated steel plate, black, 30% gloss |
Dimensions | 482.6 |
Weight | 7.4 kg |
Accessory | Power cord (2 m) ……1, Rack mounting bracket (preinstalled on the unit) ……2, Rack mounting screw ……4, Blank panel (preinstalled on the unit) ……8, Module mounting screw (spare) ……4, CD (software) …1 |
Option | Mic/Line input module: D-921E, D-921F, D-922E, D-922F Stereo input module: D-936R Digital input module: D-923AE, D-937SP Line output module: D-971E, D-971M, D-971R Digital output module: D-972AE, D-961SP Remote control module: D-981, D-983 |
[Notes]
1. When installing the unit, never block the intake vents provided in the unit’s bottom near the rear.
2. Windows is a trademark of Microsoft Corporation.
The DQ-C01 Remote Control Module is designed to permit remote control of memory selection, output volume adjustment, and output muting of TOA’s Digital Processor DP-0206 from external equipment.
Specifications
Control Input | COM and terminals 1 – 8: Open voltage: 5 V DC, short circuit current: 25 mA, removable terminal block (9 pins) |
Control | Memory selection: Direct: Max. 8 memories, Binary: 16 memories (Any one of 16 memories can be assigned to each terminal when set for Direct” mode.)” Control method: No-voltage make of over 500 ms/ No-voltage make pulse of over 500 ms (No-voltage make of over 500 ms only when set for Binary” mode.)” Volume control (Up/Down): Direct: Max. 4 groups, Binary: Max. 10 groups (Any output channel or channel group can be assigned to each terminal.) Control method: 1-step variation with no- voltage make pulse of over 500 ms. Continuous variation in 500 ms units with pulse of over 700 ms. Continuous up/down variation in 500 msec units with the addition of no-voltage make pulse of over 700 msec. Continuous volume variation stops when a break pulse is fed. Variable range: 0 to -∞ dB Muting (On/Off): Max. 8 groups (Any output channel or channel group can be assigned to each terminal.) Control method: No-voltage make of over 500 ms/ No-voltage make pulse of over 500 ms The above controls can be performed singly or in combination with other controls. |
Setting | PC software (Windows95/98/NT compatible)* |
Finish | Pre-coated steel plate, black, 30% glossy |
Dimensions | 26.5 |
Weight | 60 g |
Accessory | Mounting screw …2, Removable terminal plug (9 pins) …1 |
The DQ-D01 is a digital I/O module that expands the Digital Processor DP-0206’s input or output to 2 channels. The digital signal conforms to the AES/EBU format. Owing to the built-in sample rate converter, the module can handle signals of various sampling frequencies.
Specifications
Mode | 1 Input mode Signal format: AES/EBU (2 channels multiplexed) Connector: BNC jack Input impedance: 75 Ω Input voltage: 0.5 – 5.0 V(p-p) Sampling frequency: 32 – 48 kHz Through output: Delivers the input signal electrically buffered. 2 Output mode Signal format: AES/EBU (2 channels multiplexed) Connector: BNC jack Output impedance: 75 Ω Output voltage: 1 V(p-p) Sampling frequency: 48 kHz |
Mode Selection | Input mode or output mode (selectable by a slide switch) |
Data Length | 24 bit |
Finish | Pre-coated steel plate, black, 30% gloss |
Dimensions | 26.5 |
Weight | 90 g |
Accessory | Mounting screw…2, Label…4 |
Applicable Model | DP-0206 |
Equalizers
The E-232 has two 2/3 octave 14-point equalizers. It can be mounted in an EIA-Standard equipment rack (1-unit size).
Specifications
Power Source | 220 – 240 V AC, 50/60 Hz |
Power Consumption | 13 W |
Input | +4 dB* 30 kΩ (GAIN: 0 dB), unbalanced, phone-jack and screw terminal |
Output | +4 dB* 1 kΩ, unbalanced, phone-jack and screw terminal |
Max. Input Level | +32 dB (GAIN: -12 dB) |
Max. Output Level | +20 dB |
Frequency Response | +1 dB, -2 dB (20 Hz – 20 kHz) |
Total Harmonic Distortion |
0.01 % or less at 1 kHz (rated output) |
Equalization Center Frequency |
40 Hz, 63 Hz, 100 Hz, 160 Hz, 250 Hz, 400 Hz, 630 Hz 1 kHz, 1.6 kHz, 2.5 kHz, 4 kHz, 6.3 kHz, 10 kHz, 16 kHz |
Control Equalizaer Sliders |
Boost: +12 dB, +6 dB Cut: -12 dB, -6 dB (switchable) |
Gain Range | ±12 dB |
Highpass Filter | -12 dB/oct (Adjustable cutoff frequency 15 Hz – 300 Hz) |
Hum and Noise (IHF-A) | -98 dB* or less (EQ: ON, HPF: 15 Hz, GAIN: 0 dB, all sliders at 0 position) |
Finish | Front panel : Aluminium, black Case: Steel, black |
Dimensions | 483 |
Weight | 3.8 kg (8.38 lb) |
Accessory | Security cover …1, Security cover fixing screw …2, Rack mounting screw …4, Rubber foot …4, Blind label …1, Power cord (2 m (6.56 ft)) …1 |
The LT-102 is an output transformer. This transformer can be easily connected to the TOA’s 1,000 series equipment using connectors.
Specifications
Impedance | 600 ohm : 600 ohm |
Frequency Response | 30Hz〜20kHz at %%p0.15dB |
Distortion | Less than 0.2% (50Hz 5dB*) |
Constant loss | Within 1.5dB (at 1kHz 1v) |
Weihgt | 44g (0.1 lbs.) |
Accessories | Sleeve……2 Screw……4 |
The E-1231 is a single channel, 1/3 octave active graphic equalizer designed to allow clean, accurate audio equalization for stage, studio, or commercial applications.
Specifications
AC Line Voltage | AC mains, 50/60 Hz |
Power Consumption | 11 W 120 V version 11 W 220 – 240 V version |
Input Impedance | 10 kΩ |
Output Impedance | 600 Ω |
Frequency Response | 20 Hz – 20 kHz, %%p1 dB |
Max. Input Level | +20 dB* at 1 kHz |
Max. Output Level | +20 dB* with 600 Ω load |
Total Harmonic Distortion |
0.01% or less at 1 kHz (all sliders at 0 position, rated output) |
Equalization Center Frequency |
31.5 Hz, 40 Hz, 50 Hz, 63 Hz, 80 Hz, 100 Hz, 125 Hz, 160 Hz, 200 Hz, 250 Hz, 315 Hz, 400 Hz, 500 Hz, 630 Hz, 800 Hz, 1 kHz, 1.25 kHz, 1.6 kHz, 2 kHz, 2.5 kHz, 4 kHz, 5 kHz, 6.3 kHz, 8 kHz, 10 kHz, 12.5 kHz, 16 kHz |
Controls Equalizer Sliders |
%%p12 dB |
Input Level Control | %%p12 dB |
Highpass Filter | 12 dB per octave (Adjustable cutoff frequency: 15 Hz – 300 Hz) |
Lowpass Filter | 12 dB per octave/6 dB per octave (Adjustable cutoff frequency: 2.5 kHz – 30 kHz) |
Hum And Noise | -94 dB* (EQ in, all sliders at 0 position, 20 Hz – 20 kHz B.P.F.) |
Finish | Pannel: Aluminum, black Case: Steel, dark gray |
Dimensions | 482.6 |
Weight | 4.5 kg (9.92 lb) |
Mixers
The M-9000 Matrix Mixer is designed to be used in conjunction with optional modules and can be configured for up to 8 inputs and 8 outputs. 9000 series modules as well as existing 900 series input modules can be used. The most appropriate modules can be selected depending on applications. It is equipped with signal processing and control functions necessary for sound reinforcement, permitting all parameters to be set at the mixer. Settings data can be stored inside the unit and called up using the keys on the front panel.
Specifications
Power Source | 220 – 240 V AC, 50/60 Hz |
Power Consumption | 40 W |
Audio Input | Max. 8 channels, modular construction (modules optional) |
Audio Output | Preamplifier output 1, 2: 0 dB(*1), 600 Ω, balanced, removable terminal block (3 pins) |
Module Slot | Analog input (slot 1 – 8): -10 dB(*1), 10 kΩ, unbalanced Digital input (slot 1 – 4): 24 bit/48 kHz MIX output (slot 1 – 8): -14 dB(*1), 330 Ω (CH 1 prefader output), unbalanced Digital output (slot 5 – 7): 24 bit/48 kHz Power supply (slot 1 – 8): +24 V, -24 V, +6 V DC |
Digital Audio Signal Reference Level | -20 dBFS |
Frequency Response | 20 – 20,000 Hz, +1, -3 dB |
Total Harmonic Distortion | 0.008% (at 22 kHz LPF, 1 kHz, +10 dB(*1) output) |
S/N Ratio | At Input short, 20 – 20,000 Hz, set to ALL FLAT or OFF setting Output volume min.: 90 dB Output volume max.: 61 dB (Input 1 volume: 0 dB, Other Inputs: OFF) |
Cross Talk | Over 64 dB (at 20 kHz) |
Tone Control | Bass: ±12 dB (at 100 Hz) Treble: ±12 dB (at 10 kHz) |
Parametric Equalizer | 10 bands, Frequency: 20 – 20,000 Hz, 31 steps, Variable range: ±12 dB, Q: 0.3 – 5 |
Speaker Equalizer | 15 (compatible with TOA speakers only) |
High-pass Filter | -12 dB/oct, Variable frequency range: 20 – 400 Hz, 14 steps |
Low-pass Filter | -12 dB/oct, Variable frequency range: 4,000 – 20,000 Hz, 8 steps |
Compressor | Depth: 1 – 5 |
Delay | 0 – 40 ms (1 ms steps), maximum 40 ms (CH 1 + CH 2), mixer mode only |
Scene/Event Memory | 32 |
Operation Mode | Matrix mode/Mixer mode (selector switch) |
Auxiliary Function | Key lock function |
Control Input/Output | RS-232C(*2), D-sub connector (9 P, female) Control input: 4 inputs, no-voltage make contact input, open voltage: 3.3 V DC, short-circuit current: Under 1 mA, removable terminal block (14 pins) Control output: 4 outputs, open collector output, withstand voltage: 27 V DC, control current: 50 mA, removable terminal block (14 pins) Remote volume: 2 channels, connect a 10 kΩ/linear taper variable resistor or input the DC voltage of 0 to +10 V, removable terminal block (14 pins) |
Operating Temperature | -10℃ to +40℃ |
Operating Humidity | 35% to 80% RH (no condensation) |
Finish | Panel: Aluminum, hair-line, black Case: Surface-treated steel plate, black, paint |
Dimensions | 420 |
Weight | 6 kg |
Accessory | Power cord (2 m) …1, Rack mounting bracket …2, Bracket mounting screw …4, Blank panel …7, Blank panel mounting screw …14,Removable terminal plug (3 pins) …2, Removable terminal plug (14 pins) …1,CD-ROM …1, Start guide …1 |
(*1) 0 dB = 1 V
(*2) Allowing it to be controlled by a control system such as AMX and Crestron through RS-232C port.
The D-2008SP Digital Mixing Processor Unit is designed to have up to 32 audio inputs and outputs in total, and to be mounted in an EIA standard equipment rack (3U size). A built-in powerful signal processing function permits the unit to be used as both a mixer and a signal processor. Its audio input/output and control ports can accept optional plug-in modules, making the unit have a maximum of 32 inputs or 32 outputs and up to 2 control modules.
Using the following optional modules enables the unit to perform their functions: Two D-983s for providing a maximum of 48 contact inputs and 32 contact outputs, D-984VC for VCA control, and D-2000CB for audio data transfer between multiple D-2008SP units. Each function is set by the dedicated setting software on a PC. Setting contents can be stored in the unit’s internal memory as preset memory, which can be recalled by the D-2008SP without using a PC. The D-2012C, when connected, remotely controls the D-2008SP’s basic operations such as volume control.
Specifications
Power Source | 220 – 240 V AC, 50/60 Hz |
Power Consumption | 76 W |
Frequency Response | 20 Hz – 20 kHz, ±1 dB (+4 dB* input) |
Sampling Frequency | 48 kHz |
Input and Output | Input: Max. 32 channels, modular construction (modules optional) Output: Max. 32 channels, modular construction (modules optional) Monitor bus: 1 stereo input, 1 stereo output Connector: RJ45 connector Connection cable: Shielded Category 5 or higher twisted pair LAN cable(CAT5-STP) Maximum cable distance: 100 m (between D-2008SP and D-2012C) Headphone: 1 stereo |
Signal Processing
Feedback Suppression Function | 12 filters (auto + dynamic), maximum 4 bus channels |
Auto-Mixing Function | Ducker (automatic muting), NOM attenuation |
Auto-Mixing Group | 4 groups |
Equalizer/Filter | Parametric equalizer: 20 Hz – 20 kHz, ±15 dB, Q: 0.267-69.249 Filtering: High-pass filter 20 Hz – 20 kHz, 6 dB/oct, 12 dB/oct Low-pass filter 20 Hz – 20 kHz, 6 dB/oct, 12 dB/oct Notch filter 20 Hz – 20 kHz, Q: 8.651 – 69.249 All-pass filter 20 Hz – 20 kHz, Q: 0.267 – 69.249 High shelving filter 6 – 20 kHz, ±15 dB Low shelving filter 20 – 500 Hz, ±15 dB Horn equalizer 20 kHz, 0 to +18 dB (0.5 dB steps) Crossover filter: 20 Hz – 20 kHz, 6 dB/oct, 12 dB/oct, 18 dB/oct, 24 dB/oct |
Compressor/Auto-Leveler | (Compressor mode) Threshold: -20 to +20 dB (1 dB steps) Ratio: 1:1, 1.1:1, 1.2:1, 1.3:1, 1.5:1, 1.7:1, 2:1, 2.3:1, 2.6:1, 3:1, 4:1, 5:1, 7:1, 8:1, 10:1, 12:1, 20:1, :1 Attack time: 0.2 ms – 5 s, Release time: 10 ms – 5 s Gain: – – +10 dB Knee type: hard knee, soft knee 1, soft knee 2 (Auto-leveler mode) Target level: -20 to +10 dB (1 dB steps) Maximum gain: 0 to +20 dB (1 dB steps) Attack time: 10 ms – 10 s, Release time: 100 ms – 10 s |
Output Delay | Delay time: 0 – 1360 ms (0.021 ms steps) |
BUS Delay | Delay time: 0 – 677 ms (0.021 ms steps) |
Matrix | Input: Max. 34 ( 32 + 2 ) channels × 24 buses, Output: Max. 44 (24 + 4 + 16) buses × 32 channels |
CobraNet Matrix | Input: Max. 16 channels × 24 buses, Output: Max. 28 (24 + 4) buses × 16 channels |
Crosspoint Gain | – – 0 dB (1 dB steps) |
Preset Memory | 32 |
Auxiliary Function | Key Locking function |
LAN | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) Connected via a switching hub Network protocol: TCP/IP Connection cable: Shielded Category 5 or higher twisted pair LAN cable(CAT5-STP) Maximum cable distance: 100m(between D-2008SP and switching hub) |
Control | RS-232C: D-sub connector (9 pins) Used for external control Module: Remote control module slot: 2 |
Operating Temperature | +5 ℃ to +40 ℃ (41 ゜F to 104 ゜F) |
Finish | Panel: Aluminum, hair-line finish, black Case: Surface-treated steel plate |
Dimensions | 482 |
Weight | 6.3 kg (13.89 lb) |
Accessory | Power cord (2 m (6.5 ft)) …1, Rack mounting screw …4, CD (Set-up software) …1 Module mounting screw (spare) …4, Blank panel (preinstalled on the module slot) …8 |
Option | Mic/line input module: D-2000AD1, D-921E, D-921F, D-922E, D-922F Stereo select input module: D-936R Digital input module: D-923AE, D-937SP Line output module: D-971E, D-971M, D-971R, D-2000DA1 Digital output module: D-961SP, D-972AE CobraNet interface module: D-2000CB Remote control module: D-981, D-983 VCA control module: D-984VC |
* 0 dB = 0.775 V
The D-2012C is a 6U rack mountable Remote Console Unit designed for exclusive use with the D-2008SP Digital Mixing Processor Unit. Assigned to any desired channels inside the D-2008SP by the dedicated software, the D-2012C’s 12 motorized faders and 8 rotary encoders can remotely adjust their volumes. Desired preset memories can be recalled using 8 function keys.
It is equipped with 1 channel line input (stereo), which allows the audio signal to be transmitted to the D-2008SP via monitor bus. Audio signals inside the D-2008SP can be monitored via monitor bus through headphones connected to a stereo headphone output. The D-2012C can be installed on a desk with the additional use of an optional D-2012AS Console Case.
Specifications
Power Source | 220 – 240 V AC |
Power Consumption | 18 W |
Volume Adjustment | 100 mm motorized fader x 12 Rotary encoder x 8 |
Line Input | 1 channel (stereo) |
Headphone Output | Stereo 100 mW + 100 mW (32 Ω load) |
Monitor Bus | 1 stereo input Connector: RJ45 connector Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable (2 pairs of data lines) Maximum cable distance: 100 m (109.36 yd) (between D-2012C and D-2008SP) |
LAN | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation) RJ45 connector Network protocol: TCP/IP Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable Maximum cable distance: 100 m (109.36 yd) (between D-2008SP and switching hub) |
Control | RS-232C: D-sub connector (9 pins) for maintenance use |
Finish | Panel: Surface-treated steel plate Rack mounting bracket: Surface-treated steel plate |
Dimensions | 482 |
Weight | 6.6 kg (14.55 lb) |
Accessory | Power cord (2 m (6.5 ft)) ……1 Fader knob (yellow) ……3 |
Option | Console case: D-2012AS |
The D-2000AD1 is a 4-channel Microphone/Line Input Module designed for use with the D-2008SP Digital Mixing Processor Unit. It employs XLR type connectors.
Specifications
Input | 4 channels, Mic/Line selectable Mic: -50/-36 dB*, 2.6 kΩ, electronically-balanced Line: -10 dB*, 2.6 kΩ/+4 dB*, 7 kΩ, electronically-balanced Connector: XLR-3-31 equivalent Phantom power supply (48 V DC, can be used when set for the Mic) Ground lift switch |
A/D Converter | 24 bit |
Sampling Frequency | 48 kHz |
Frequency Response | 20 Hz – 20 kHz, ±1 dB (+4 dB* input) |
Dynamic Range | 104 dB (IHF-A weighted) or more (+4 dB* input) |
Total Harmonic Distortion | 0.008 % or less (+4 dB* input) |
Finish | Panel: Pre-coated steel plate, black, 30 % gloss |
Dimensions | 35 |
Weight | 200 g (0.44 lb) |
The D-921E is a 2-channel microphone/line input module designed for use with the D-901 Digital Mixer, etc. It is equipped with removable terminal block type connectors. Input sensitivity and phantom power setting can be performed at the main frame such as the D-901.
Specifications
Input | 2 channels, Mic/Line changeable Mic: -50/-36 dB*, 4.7 kΩ, electronically-balanced, removable terminal block (3 pins) Line: -10/+4 dB*, 10 kΩ, electronically-balanced, removable terminal block (3 pins) Phantom power supply (can be used when set for the microphone) 15 V: D-901 (option), DP-K1 (option), D-2008SP (option) 12 V: SX-2100AI (option) Ground lift switch |
A/D Converter | 24 bit |
Sampling Frequency | 48 kHz |
Frequency Response | 20 Hz – 20 kHz, ±1 dB (+4 dB* input) |
Dynamic Range | 100 dB (IHF-A weighted) or more (+4 dB* input) |
Total Harmonic Distortion |
0.05 % or less (+4 dB* input) |
Finish | Panel: Pre-coated steel plate, black, 30 % gloss |
Dimensions | 35 |
Weight | 140 g |
Accessory | Removable terminal plug (3 pins, preinstalled on the unit) …2 |
The D-921F is a 2-channel microphone/line input module designed for use with the D-901 Digital Mixer, etc. It is equipped with XLR connectors. Input sensitivity and phantom power setting can be performed at the main frame such as the D-901.
Specifications
Input | 2 channels, Mic/Line changeable Mic: -50/-36 dB*, 4.7 kΩ, electronically-balanced, equivalent to XLR-3-31 type Line: -10/+4 dB*, 10 kΩ, electronically-balanced, equivalent to XLR-3-31 type Phantom power supply (can be used when set for the microphone) 15 V: D-901 (option), DP-K1 (option), D-2008SP (option) 12 V: SX-2100AI (option) Ground lift switch |
A/D Converter | 24 bit |
Sampling Frequency | 48 kHz |
Frequency Response | 20 Hz – 20 kHz, ±1 dB (+4 dB* input) |
Dynamic Range | 100 dB (IHF-A weighted) or more (+4 dB* input) |
Total Harmonic Distortion |
0.05 % or less (+4 dB* input) |
Finish | Panel: Pre-coated steel plate, black, 30 % gloss |
Dimensions | 35 |
Weight | 150 g |
The D-922E is a 2-channel microphone/line input module designed for use with the D-901 Digital Mixer, etc. It is equipped with removable terminal block type connectors. The D-901’s 4-pole DIP switch is used to set the input sensitivity, phantom power supply, and ground lifting.
Specifications
Input | 2 channels, -50/-36/-10/+4 dB* (Selectable with the DIP switch.), 4.7 kΩ, electronically-balanced, removable terminal block (3 pins) Phantom power supply (can be set with the DIP switch) 15 V: D-901 (option), DP-K1 (option), D-2008SP (option) 12 V: SX-2100AI (option) Ground lift switch (can be set with the DIP switch) |
A/D Converter | 20 bit |
Sampling Frequency | 48 kHz |
Frequency Response | 20 Hz – 20 kHz, ±1 dB (+4 dB* input) |
Dynamic Range | 85 dB (IHF-A weighted) or more (+4 dB* input) |
Total Harmonic Distortion |
0.2 % or less (+4 dB* input) |
Finish | Panel: Pre-coated steel plate, black, 30 % gloss |
Dimensions | 35 |
Weight | 125 g |
Accessory | Removable terminal plug (3 pins, preinstalled on the unit) …2 |
* 0 dB = 0.775 V
The D-922F is a 2-channel microphone/line input module designed for use with the D-901 Digital Mixer, etc. It is equipped with XLR connectors. The D-901’s 4-pole DIP switch is used to set the input sensitivity, phantom power supply, and ground lifting.
Specifications
Input | 2 channels, -50/-36/-10/+4 dB* (Selectable with the DIP switch.), 4.7 kΩ, electronically-balanced, equivalent to XLR-3-31 type Phantom power supply (can be set with the DIP switch) 15 V: D-901 (option), DP-K1 (option), D-2008SP (option) 12 V: SX-2100AI (option) Ground lift switch (can be set with the DIP switch) |
A/D Converter | 20 bit |
Sampling Frequency | 48 kHz |
Frequency Response | 20 Hz – 20 kHz, ±1 dB (+4 dB* input) |
Dynamic Range | 85 dB (IHF-A weighted) or more (+4 dB* input) |
Total Harmonic Distortion |
0.2 % or less (+4 dB* input) |
Finish | Panel: Pre-coated steel plate, black, 30 % gloss |
Dimensions | 35 |
Weight | 135 g |
LINE OUTPUT MODULE
The D-2000DA1 Line Output Module is designed for use with the D-2008SP Digital Mixing Processor Unit and features high quality sound. The output level of each output terminal can be independently set to either +4 dB or -10 dB and its output mode independently set to either balanced or unbalanced type by the built-in DIP switch. It employs XLR type connectors.
Specifications
Output | 4 channels, +4 dB*/-10 dB* (changeable), adaptable load of 600 Ω or more, balanced (electronically-balanced)/unbalanced (changeable), XLR-3-32 equivalent |
D/A Converter | 24 bit |
Sampling Frequency | 48 kHz |
Frequency Response | 20 Hz – 20 kHz, ±1 dB |
Dynamic Range | 104 dB (IHF-A weighted) or more |
Total Harmonic Distortion |
0.008 % or less |
Finish | Panel: Pre-coated steel plate, black, 30 % gloss |
Dimensions | 35 |
Weight | 200 g (0.44 lb) |
The D-971E is a 4-channel line output module designed for use with the D-901 Digital Mixer, etc. It is equipped with removable terminal block type connectors.
Specifications
Output | 4 channels, +4 dB*, adaptable load of over 600 Ω, electronically-balanced, removable terminal block (3 pins) |
D/A Converter | 24 bits |
Sampling Frequency | 48 kHz |
Frequency Response | 20 – 20,000 Hz, ±1 dB |
Dynamic Range | Over 100 dB (IHF-A weighted) |
Total Harmonic Distortion |
Under 0.05% |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 140 g |
Accessory | Removable terminal plug (3 pins, preinstalled on the unit) …4 |
The D-971M is a 4-channel line output module designed for use with the D-901 Digital Mixer, etc. It is equipped with XLR connectors.
Specifications
Output | 4 channels, +4 dB*, adaptable load of over 600 Ω, electronically-balanced, equivalent to XLR-3-32 type |
D/A Converter | 24 bits |
Sampling Frequency | 48 kHz |
Frequency Response | 20 – 20,000 Hz, ±1 dB |
Dynamic Range | Over 100 dB (IHF-A weighted) |
Total Harmonic Distortion |
Under 0.05% |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 165 g |
The D-971R is a 4-channel line output module designed for use with the D-901 Digital Mixer, etc. It is equipped with standard RCA pin jacks.
Specifications
Output | 4 channels (2 outputs for each channel), -10 dB*, adaptable load of over 600 Ω, RCA pin jack |
D/A Converter | 24 bits |
Sampling Frequency | 48 kHz |
Frequency Response | 20 – 20,000 Hz, ±1 dB |
Dynamic Range | Over 100 dB (IHF-A weighted) |
Total Harmonic Distortion |
Under 0.05% |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 150 g |
The D-2000CB is designed for use with the D-2008SP Digital Mixing Processor Unit. When mounted to the D-2008SP, it allows audio transmission between this D-2008SP and other one. Each function is set by the dedicated setting software on a PC.
Specifications
Network I/F | CobraNet: 100BASE-TX, PRIMARY/SECONDARY 2 system, RJ45 connector, Enables decentralized installation, Audio transmission only Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable To be connected via the specified switching hub Note: This network should be completely independent of other LAN. Number of D-2008SP connection: Max. 4 Switching hub stage: Max. 7 Max extend distance: 100m (328.1 ft) (connected via a switching hub) |
Input | 16 channels, 20 bit/24 bit |
Output | 16 channels, 20 bit/24 bit |
Sampling Frequency | 48 kHz |
Finish | Panel: Pre-coated steel plate |
Dimensions | 17 |
Weight | 100 g (0.22 lb) |
Accessory | Panel …1, Screw …3 |
The D-911 is a dedicated VCA fader unit designed for use with the D-901 Digital Mixer, etc. Connecting the D-911 to the D-984VC, VCA control module permits the volume control of all channels and contact controls.
Specifications
Power Supply | 5 V DC (supplied from the optional D-984VC) |
Connector | RJ45 connector × 8 |
Input Fader Control | Input fader (100 mm) × 12 |
Output Volume Control | Output volume control × 8 |
Contact Control | Illuminated switch × 8 |
Remote Output | No-voltage make contact output (contact capacity: 30 V DC, 4 A) |
Remote Switch | Seesaw switch for activating the remote function of the power distributor |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 482.6 |
Weight | 2.7 kg |
Accessory | Fader knob (Red, Yellow)…3 each, Volume knob (Red)…2, Rack mounting screw…4, Rack mounting bracket (preinstalled on the unit)…2 |
DIGITAL INPUT MODULE
The D-923AE is a 2-channel line digital input module designed for use with the D-901 Digital Mixer, etc. With the use of this module, digital signals can be input, permitting direct connection of the D-901 Digital Mixer to equipment having a digital output. Owing to the built-in sample rate converter, the module can handle signals of various sampling frequencies.
Specifications
Input | 2 channels, 2.0 – 7.0 V (p-p), 110 Ω, XLR-3-31 or equivalent |
Applicable Format | AES/EBU (2 channel multiplexed) |
Sampling Frequency | 32 – 48 kHz |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 130 g |
The D-937SP is a 1 stereo channel line digital input module designed for use with the D-901 Digital Mixer, etc. With the use of this module, digital signals can be input, permitting direct connection of the D-901 Digital Mixer to equipment having a digital output. Owing to the built-in sample rate converter, the module can handle signals of various sampling frequencies. When this module is used, one of four stereo inputs is selected for output to the D-901. Input selection can be performed at the front panel, by PC software or through a remote control module.
Specifications
Input | Stereo 1 channel line (Selectable one of four inputs) 0.5 V (p-p), 75 Ω, Coaxial RCA jack × 2 Square optical connector × 2 |
Applicable Format | S/PDIF (2 channel multiplexed) |
Sampling Frequency | 32 – 48 kHz |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 130 g |
The D-936R is a 4 stereo input module designed for use with the D-901 Digital Mixer, etc. It is equipped with standard RCA pin jacks. The D-936R features two stereo transmission modes: 1)Selection of one of the four stereo inputs for transmission to the D-901. 2)Mixing of all four stereo inputs, transmitting the mixed signal to the D-901 through left/right channel outputs. Mode settings and stereo selection are performed at the main frame such as the D-901.
Specifications
Input | 1) When the module is attached to the D-901 (option) or D-2008SP (option) or DP-K1 (option); stereo × 4 inputs (Selection of 1 stereo or mixing or all 4 stereo inputs) -10 dB*, 10 kΩ, RCA pin jack 2) When the module is attached to the SX-2100AI (option); monaural × 2, -10 dB*, 10 kΩ, RCA pin jack |
A/D Converter | 24 bit |
Sampling Frequency | 48 kHz |
Frequency Response | 20 Hz – 20 kHz, ±1 dB (+4 dB* input) |
Dynamic Range | 100 dB (IHF-A weighted) or more |
Total Harmonic Distortion |
0.05 % or less |
Finish | Panel: Pre-coated steel plate, black, 30 % gloss |
Dimensions | 35 |
Weight | 145 g |
The D-961SP is a Stereo 2-channel line digital output module designed for use with the D-901 Digital Mixer, etc. With the use of this module, digital signals can be output, permitting direct connection of the D-901 Digital Mixer to equipment having a digital input. Each pair of optical output and coaxial output is output in parallel.
Specifications
Output: | Stereo 2 channel line (with splitter, can be output to each pair of optical output and coaxial output in Parallel), 0.5 V (p-p) 75 Ω, Coaxial RCA jack × 2, Square optical connector × 2 |
Applicable Format | S/PDIF (2 channel multiplexed) |
Sampling Frequency | 48 kHz |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 130 g |
The D-972AE is a 4-channel line digital output module designed for use with the D-901 Digital Mixer, etc. With the use of this module, digital signals can be output, permitting direct connection of the D-901 Digital Mixer to equipment having a digital input.
Specifications
Output | 4 channels, 5.0 V (p-p), 110 Ω, XLR-3-32 or equivalent × 2 |
Applicable Format | AES/EBU (2 channel multiplexed) |
Sampling Frequency | 48 kHz |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 130 g |
Accessory | Ferrite clamp…2 |
The D-981 is a remote control module designed for use with the D-901 Digital Mixer, etc. It permits preset memory recall, input/output channel volume control, stereo input selection and channel ON/OFF operation to be remotely controlled from external equipment. Tally output can also be provided for external control.
Specifications
Contact Input | COM + Terminals 1 – 8: Open voltage: 5 V DC, short-circuit current: 5 mA removable terminal block (10 pins) |
Control
Preset Memory Selection |
Any preset memory can be recalled. Control method: No-voltage make of over 100 ms/ |
Volume Control | Any input/output channel volume can be turned UP or Down. Control method: 1 step variation for no-voltage make single pulse of over 100 ms 1 step continuous operation for every 70 ms for no-voltage make of over 100ms. Can be reset when at break. Variable range : -∞ dB to +10 dB |
Channel | Any input/output channel can be turned ON and OFF. Control method: No-voltage make of over 100 ms/ no-voltage make single pulse of over 100 ms |
Stereo Selection | Input channel lines of the D-936R (optional), or the D-937SP (optional) (4 stereo input module) can be selected. Control method: No-voltage make of over 100 ms/ No-voltage make single pulse of over 100 ms |
Contact Output | COM + Terminals 1 – 8: No-voltage make contact input, contact capacity: 24 V DC, 100 mA removable terminal block (10 pins) |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 125 g |
Accessory | Removable terminal plug (10 pins, preinstalled on the unit) …2 |
The D-983 is a remote control module designed for used with the D-901 Digital Mixer, etc. It permits preset memory recall, input/output channel volume control, stereo input selection and channel ON/OFF operation to be remotely controlled from external equipment. Tally output can also be provided for external control.
Specifications
Contact Input | COM + Terminal 1 – 24: Open voltage: 5 V DC, short-circuit current: 5 mA, RJ45 connector × 4 |
Control
Preset Memory Selection |
Any preset memory can be recalled. Control method: No-voltage make of over 100 ms/ No-voltage make single pulse of over 100 ms |
Volume Control | Any input/output channel volume can be turned UP or DOWN. Control method: 1 step variation for no-voltage make single pulse of over 100 ms 1 step continuous operation for every 70ms for no-voltage make of over 100ms. Can be reset when at break. Variable Range: -∞ dB to +10 dB |
Channel | Any input/output channel can be turned ON and OFF. Control method: No-voltage make of over 100 ms/ No-voltage make single pulse of over 100 ms |
Stereo Selection | Input channel lines of the D-936R (optional), or the D-937SP (optional) (4 stereo input module) can be selected. Control method: No-voltage make of over 100 ms/ No-voltage make single pulse of over 100 ms |
Contact Output | COM + Terminals 1 – 16: No-voltage make contact, contact capacity: 24 V DC, 100 mA, RJ45 connector × 4 |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 170 g |
The D-984VC is a dedicated VCA control module designed for use with the D-901 Digital Mixer. It expands the D-901 Digital Mixer’s functions by 20 VCA control inputs, 8 contact inputs, and 8 contact outputs. By the VCA controls from external equipment, this module permits the D-901’s gains of 12 inputs and 8 outputs to be controlled. By the contact input controls from external equipment, this module permits the preset memory recall, input/output channel gains, stereo input selection, and channel ON/OFF to be controlled. By the contact output controls Tally outputs can also be provided for external control.
Specifications
VCA Control Input | +5 V, GND, Terminal 1 – 20 (12 Input channels, 8 output channels), RJ45 connector × 4 Control contents: Volume control of each input/output channel Variable range: – dB to + 0 dB |
Contact Input | COM + Terminal 1 – 8: Open voltage: 5 V DC, short-circuit current: 5 mA, RJ45 connector × 2 |
Control
Preset Memory Selection |
Any preset memory can be recalled. Control method: No-voltage make of over 100 ms/ No-voltage make single pulse of over 100 ms |
Volume Control | Any input/output channel volume can be turned UP or DOWN. Control method: 1 step variation for no-voltage make single pulse of over 100 ms 1 step continuous operation for every 70ms for no-voltage make of over 100ms. Can be reset when at break. Variable Range: – dB to +10 dB |
Channel | Any input/output channel can be turned ON and OFF. Control method: No-voltage make of over 100 ms/ No-voltage make single pulse of over 100 ms |
Stereo Selection | Input channel lines of the D-936R (optional), or the D-937SP (optional) (4 stereo input module) can be selected. Control method: No-voltage make of over 100 ms/ No-voltage make single pulse of over 100 ms |
Contact Output | COM + Terminal 1 – 8: No-voltage make contact, contact capacity: 24 V DC, 100 mA, RJ45 connector × 2 |
Finish | Panel: Pre-coated steel plate, black, 30% gloss |
Dimensions | 35 |
Weight | 170 g |